697425
12
Zoom out
Zoom in
Previous page
1/28
Next page
12 | Commissioning
AGS10-2, AGS10E-2, AGS20-2, AGS50-26 720 811 270 (2015/04)
5.7 Installing temperature sensors
The temperature sensors are not polarity sensitive. There are two
sensors, one identified for the Solar collector and one for the cylinder
storage; ensure that these be installed in the correct sensor pockets.
If the cable of the collector temperature sensor is joined to the sensor
lead going to the controller at a point which is exposed to moisture, a
waterproof junction box must be used [2].
If required, extend the sensor lead with a 2-wire cable [3] on site:
up to 50 m = 2 x 0.75 mm
2
up to 100 m = 2 x 1.5 mm
2
Fig. 18 Temperature sensor on solar pump station with integral
controller
[1] Collector temperature sensor
[2] Connection point
[3] 2-wire cable (on site)
[4] Fill & drain valve for emptying (not supplied)
[5] Cylinder temperature sensor, bottom
6 Commissioning
6.1 Use of heat transfer fluid
The heat transfer fluid is pre-mixed and ready to use. It guarantees safe
operation within the specified temperature range, protects the system
from frost damage and minimises risk of vaporisation.
The heat transfer medium is biodegradable. A safety data sheet with
further information can be requested from the manufacturer.
Only operate collectors with the following heat transfer medium
(available as an accessory):
6.2 Purging and filling with a hand pump (air vent on roof)
7747006489-19.2ST
524
1
3
2
NOTICE: Collector damage through evaporation in the
solar circuit or frozen water.
Flush and fill the solar system only when the sun is not
shining on the collectors and (if flushing with water)
no frost is expected.
When filling with heat transfer medium, take the
additional volume of the pre-cooling vessel into account
(if installed).
The pre-cooling vessel and the expansion vessel must be
adequately vented.
The pump in the solar pump station is self-venting. Do
not vent it by hand.
CAUTION: Risk of injury through contact with heat
transfer medium
When handling heat transfer fluid, always wear
protective gloves and goggles.
If heat transfer medium comes into contact with skin:
wash off with water and soap.
▶If heat transfer fluid comes into contact with eyes:
thoroughly rinse eyes with running water and if
required seek medical advice.
NOTICE: Using an unsuitable heat transfer medium may
damage the system and will invalidate the warranty.
▶Do not mix heat transfer medium with other heat
transfer media.
If the solar system is not in use for more than 4 weeks,
cover the collectors.
Collector version
Heat transfer
medium
Temperature range
Flat plate Type L – 28 ... +170 °C
Evacuated tube Type LS – 28 ... +170 °C
Table 8
NOTICE: Collector damage.
With vacuum tube collectors, always use pressure
filling ( Chapter 6.2) because water must not be
poured into the collectors.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch AGS20-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch AGS20-2 in the language / languages: English as an attachment in your email.

The manual is 2,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info