697425
11
Zoom out
Zoom in
Previous page
1/28
Next page
Installing the solar pump station | 11
6 720 811 270 (2015/04)AGS10-2, AGS10E-2, AGS20-2, AGS50-2
Connect the expansion vessel [3] in the return on the solar pump
station's safety assembly.
Fig. 16
[1] Pressure relief valve
[2] Flexible stainless steel hose from the connection set (available as
accessory)
[3] Expansion vessel
5.5.3 Adjusting the pre-charge pressure of the expansion vessel
To make use of the maximum possible volume:
Set the pre-charge pressure when the vessel is not subjected to load
(i.e. no fluid pressure).
If the calculated pre-charge pressure is higher or lower than the
factory-set pre-charge pressure (see table 7, page 11), correct the
pre-charge pressure accordingly.
5.6 Connecting pipework and pressure relief valve
discharge pipe to the solar pump station
Cut the pipes to length and push them as far as possible into the
compression fitting [1].
Route the discharge pipe [2] from the pressure relief valve so that any
discharge can be seen to empty out into the holding container [4] and
secure it in place with a pipe clip [3].
Maintain an air break.
Fig. 17 Connection to solar pump station
[1] Compression joints on all four outlets
[2] Discharge pipe (not supplied)
[3] Pipe clip (on site)
[4] Empty solar fluid container (holding container)
[5] Connection bracing points
The pre-charge pressure of the expansion vessel is
calculated based on the static system head
1)
plus an
allowance.
Calculate and set pre-charge pressure to at least
1.2 bar.
Flat plate Evacuated tube
Static height
1)
1) A one metre difference in height (between collector array and solar pump station)
equates to 0.1 bar
(10 m) 1.0 bar (10 m) 1.0 bar
+ allowance + 0.4 bar + 1.7 bar
= expansion vessel pre-
charge pressure
= 1.4 bar = 2.7 bar
Table 7 Example: collector-dependent pre-charge pressure
6720801165.16-2.ST
1
2
3
WARNING: Injuries and system damage due to hot heat
transfer medium.
Make sure the discharge pipe size is at least that of the
pressure relief valve (maximum length = 2 m and
maximum of 2 bends).
To tighten the lower compression fittings, you can brace
against the points marked [5] using a 27 mm spanner or
pipe wrench.
7747006489.49-2.ST7747006489.49-2.ST
3
141
1
1
2
5
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch AGS20-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch AGS20-2 in the language / languages: English as an attachment in your email.

The manual is 2,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info