707739

Bosch AdvancedGrind 18 Manual

22
Zoom out
Zoom in
Previous page
1/293
Next page
22 | English
1 609 92A 47W | (24.11.17) Bosch Power Tools
Approved Grinding Tools
All grinding tools mentioned in these operating instructions
can be used.
The permissible speed [min
-1
] or the circumferential speed
[m/s] of the grinding tools used must at least match the values
given in the table.
Therefore, observe the permissible rotational/circumferen-
tial speed on the label of the grinding tool.
Dust/Chip Extraction
Dust from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one’s health. Touching or breathing-in the dust can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dust, such as oak or beech dust, is considered car-
cinogenic, especially in connection with wood-treatment
additives (chromate, wood preservative). Materials con-
taining asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
Prevent dust accumulation at the workplace. Dust can
easily ignite.
Operation
Hold the power tool by the insulated gripping surfaces
23 and by the auxiliary handle 8 when performing an
operation where the application tool may contact hid-
den wiring. An application tool contacting a “live” wire
may make exposed metal parts of the power tool “live” and
could give the operator an electric shock.
Starting Operation
Inserting the battery
Insert the charged battery 5 from above into the base of the
power tool until the battery is securely locked.
Switching On and Off
To start the power tool, push the On/Off switch 3 forwards.
To lock the On/Off switch 3, press the On/Off switch 3 down
at the front until it latches.
To switch off the power tool, release the On/Off switch 3 or,
if it is locked, briefly push down the back of the On/Off switch
3 and then release it.
To save energy, only switch the power tool on when using it.
Check grinding tools before using. The grinding tool
must be mounted properly and be able to move freely.
Carry out a test run for at least one minute with no load.
Do not use damaged, out-of-centre or vibrating grind-
ing tools. Damaged grinding tools can burst and cause
injuries.
Restarting Protection
The restarting protection feature prevents uncontrolled
restarting of the machine after an interruption in the power
supply.
To restart the operation, switch the On/Off switch 3 to the
Off position and start the machine again.
Constant Electronic Control
Constant electronic control holds the speed constant at
no-load and under load, and ensures uniform working perfor-
mance.
Soft Starting
The electronic soft starting feature limits the torque upon
switching on and increases the working life of the motor.
Speed preselection
The required speed can be preselected with the thumbwheel 7 (also while running).
The data in the following table are recommended values.
max.
[mm]
[mm]
D b d [min
-1
] [m/s]
115
125
6
6
22.2
22.2
10000
10000
80
80
115
125
–
–
–
–
10000
10000
80
80
75 30 M 14 10000 45
D
D
b
d
Material Application Accessory Thumbwheel Position
Metal Removing paint Sanding pad with sanding sheet 2–3
Wood, metal Brushing, rust removal Cup brush, sanding disc 3
Metal, masonry Grinding Grinding disc 4–6
Metal Rough grinding Grinding disc 6
Metal Cutting Cutting disc 6
OBJ_BUCH-2850-004.book Page 22 Friday, November 24, 2017 11:44 AM
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch AdvancedGrind 18 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch AdvancedGrind 18 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 26,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info