Manual Bosch AdvancedAquatak 140 (page 19 of 294) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

707726

Zoom out

Zoom in

1/294

English | 19

Problem Possible Cause Corrective Action

Fuses blow Fuses incorrectly rated Change to a mains supply higher than the pres-

sure washer amp consumption

Motor starts but no

pressure

Nozzle partly blocked Clean nozzle

Motor “sounds” but

fails to start

Insufficient power supply Check that the voltage of the mains power supply

line is the same as that on the plate.

Voltage loss due to use of extension cable Check characteristics of extension cable

Appliance not used for a long period of time Contact your Bosch Service Centre

Problems with TSS (Total Stop System) device Contact your Bosch Service Centre

Pressure pulsating Air in the inlet water supply hose/pump Allow pressure washer to run with open spray

handle and nozzle at low pressure until regular

working pressure is obtained

Inadequate water supply Check that the water supply corresponds to spe-

cifications. The minimum specification for the wa-

ter supply hose is 1/2" or 13mm diameter

Water filter blocked Clean water filter

Water supply hoses squeezed Straighten out kinked water supply hoses

High pressure hose too long Remove high pressure extension hose. Retry (ex-

tension hose max. 7m)

Pressure too low, but

steady

Note: Several types of

accessory will normally

deliver a lower pres-

sure

Nozzle worn Change the nozzle

Start/stop valve worn Activate trigger five times in quick succession

Motor starts up but

with restricted or no

working pressure

No water supply Connect water supply

Water filter clogged up Clean the water filter

Nozzle clogged up Clean nozzle

The pressure washer

starts irregularly by it-

self

Pump/ power gun leaky Contact your Bosch Service Centre

Water leaks from ma-

chine

Leaking pump A slight water leak is permissible; in case of ex-

cessive leak, contact Bosch Service Centre.

Maintenance and Service

Maintenance

u Stop, remove plug from the power supply and discon-

nect from water supply.

Note: To ensure long and reliable service, carry out the fol-

lowing maintenance regularly.

Regularly check for obvious defects such as loose fixings,

and worn or damaged components.

Check that covers and guards are undamaged and correctly

fitted. Carry out necessary maintenance or repairs before

using.

In order to avoid safety hazards, if the power supply cord

needs to be replaced, this must be done by Bosch or by an

after-sales service centre that is authorised to repair Bosch

power tools.

After use/Storage

Turn the main switch off and operate the trigger to drain the

water from the high pressure hose.

Clean the exterior of the machine thoroughly using a soft

brush or cloth. Do not use water, solvents or polishes. Re-

move all debris, especially from the ventilation slots.

End of season storage: Drain water out of pump running mo-

tor for a few seconds. Pull trigger to release all water.

Do not place other objects on top of the machine.

Store in a frost-free area.

Ensure cables are not trapped when storing. Do not kink high

pressure hose.

After-sales Service and Application Service

www.bosch-do-it.com

Bosch Power Tools F 016 L81 693 | (30.04.2019)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch AdvancedAquatak 140 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,82 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch AdvancedAquatak 140 Manual

Product: