Manual Bosch AdvancedAquatak 140 (page 17 of 294) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

707726

Zoom out

Zoom in

1/294

English | 17

3 600 HA7 D..

– Sound power level dB(A)

– Uncertainty K dB

= 3

Wear hearing protection!

Vibration total values a

(triax vector sum) and uncertainty K determined

according to EN60335-2-79

– Vibration emission value a

m/s

0.5

– Uncertainty K m/s

= 0.5

Mounting and Operation

Action Figure Page

Delivery scope

A 279

Adjusting the Handle

B 279

Connecting high pressure gun

to lance

C 280

Connecting high pressure wa-

ter supply hose/nozzle

D 280

Attaching Nozzle

Adjusting water jet

E – F 281 - 282

Connect detergent bottle

G 283

Connecting to the water supply

H 284

Switching On and Off

I 284

Clean the water filter

J 285

Clean nozzle

K 285

Gun storage

L 286

Gun/lance/nozzle stored during

work breaks

M 286

Storage

M 286

Selecting Accessories

N 287

Switching on

For Your Safety

Warning: Switch off, remove plug from

mains before adjusting, cleaning or if cable

is cut, damaged or entangled.

The operating voltage is 230VAC, 50Hz (for non-EU coun-

tries 220V, 240V as applicable). Contact your Bosch Ser-

vice Centre for details. If in doubt contact a qualified electri-

cian or the nearest Bosch Service Centre.

If you want to use an extension cable when operating your

high pressure washer, only the following cable dimensions

should be used:

– 2.5mm

– max length 25m

Note: If an extension cable is used it must be earthed and

connected through the plug to the earth cable of your supply

network in accordance with prescribed safety regulations.

If in doubt contact a qualified electrician or the nearest

Bosch Service Centre.

WARNING! Inadequate extension cables can

be dangerous. Extension cable, plug and

socket must be of watertight construction

and intended for outdoor use.

The connections (plugs and sockets) should be kept dry and

off the ground.

For increased electrical safety use a Residual Current Device

(RCD) with a tripping current of not more than 30mA. Al-

ways check your RCD every time you use it.

If the supply cord is damaged, it must be replaced by a

Bosch Service Centre.

For products not sold in GB:

Warning: For your safety, it is required that the plug at-

tached to the product is connected with the extension cord.

The coupling of the extension cord must be protected

against splash water, be made of rubber or coated with rub-

ber. The extension cord must be used with a cable strain re-

lief.

Products sold in GB only:

Your product is fitted with an BS 1363/A approved electric

plug with internal fuse (ASTA approved to BS 1362).

If the plug is not suitable for your socket outlets, it should be

cut off and an appropriate plug fitted in its place by an au-

thorised customer service agent. The replacement plug

should have the same fuse rating as the original plug.

The severed plug must be disposed of to avoid a possible

shock hazard and should never be inserted into a mains

socket elsewhere.

u Products that are only sold in AUS and NZ: Use a resid-

ual current device (RCD) with a nominal residual current

of 30 mA or less.

Operation

u To prevent damage to the appliance, do not allow it to

operate dry.

Starting

Attach water supply hose (not supplied) to the mains water

supply and machine.

Connect the product to the mains supply ensuring that the

mains switch is in the off position.

Open water tap.

Press the safety lock (back button on the gun handle) to re-

lease the trigger. Fully press the trigger until there is a con-

Bosch Power Tools F 016 L81 693 | (30.04.2019)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch AdvancedAquatak 140 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,82 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch AdvancedAquatak 140 Manual

Product: