97284
19
Zoom out
Zoom in
Previous page
1/126
Next page
English | 193 609 929 A78 8.8.06
Inserting
Press in the pin on the drive square of the bit holder 11,
e. g., with the aid of a small screwdriver, and slide the
tool bit 12 over the drive square. Take care that the pin
engages in the recess of the tool bit.
Removing
Press in the pin in the recess of the tool bit 12 and pull
the tool bit out of the tool holder 11.
Operating Instructions
Putting into Operation
The air tool operates optimally with a pressure of
6.3 bar (91 psi) measured at the air inlet with the tool
running.
f Pay attention to the direction of rotation that
is set before switching on the pneumatic tool.
For example, when a screw is to be loosened and
the direction of rotation is set so that the screw is
tightened, this can lead to a strong torque reaction
of the pneumatic tool.
Reversing the Rotational Direction
Right rotation: To screw in screws, turn the rotational
direction switch 9 in the given direction of the arrow to
the leftuntil it stops.
Left rotation: To loosen or to unscrew screws, turn
the rotational direction switch 9 in the given direction of
the arrow to the right until it stops.
f Operate the rotational direction switch 9 only
when the pneumatic tool is at a standstill.
Switching On and Off
Note: If the tool does not start after, for example, not
being used for a long period of time, disconnect the air
supply and turn the motor repeatedly by rotating the
tool bit holder 11. This eliminates adhesive forces.
The screwdriver have a shut-off clutch
that depends on the torque and can be set
in the given range. It responds when the
torque that is set is reached.
Switching on: Press the on/off switch 5 to the
stop.The screwdriver switches off automatically when
the adjusted torque setting is reached.
Switching off: Release the on/off switch 5.
f When the on/off switch 5 is released prema-
turely, the preset torque is not reached.
Working Instructions
f Disconnect the air hose from the air source
before making any adjustments, changing
accessories, or storing the pneumatic tool.
Such preventive safety measures reduce the risk of
starting the pneumatic tool accidentally.
f Place the tool bit onto the nut/screw only
when the screwdriver is switched off. Rotating
tool bits can slide off the nut/screw.
f In the event of an interruption of the air sup-
ply or reduced operating pressure, switch off
the pneumatic tool. Check the operating pres-
sure and restart the tool when the operating
pressure is again optimal.
Excess loads that cause the pneumatic tool to stall or
reduce speed will not damage the motor.
12
11
9
5
OBJ_BUCH-220-001.book Page 19 Tuesday, August 8, 2006 9:41 AM
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch 0 607 452 603 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch 0 607 452 603 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 13,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info