Manual Boretti PRO 100 IX (page 8 of 48) (English, German, Dutch, French, Italian, Spanish)

121734

Zoom out

Zoom in

1/48

Thank you for buying a BORETTI product which has been manufactured to the highest quality standards to meet your require-

ments.

We recommend you carefully read this booklet in which you will ﬁnd instructions for installation, hints for use and mainte

nance.

1 ELECTRICAL

• This cooker hood is ﬁtted with a 3-core mains cable with a standard 10/16A earthed plug.

• Alternatively the hood can be connected to the mains supply via a double-pole switch having 3mm minimum contact gap

on each pole.

• Before connecting to the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate inside

the cooker hood.

• Technical Speciﬁcation: Voltage 220-240, single phase ~50Hz / 220 V - 60 Hz.

2 INSTALLATION ADVICE

• Ensure the cooker hood is ﬁtted in compliance with the recommended ﬁxing heights.

• To ensure the safe operation of this cooker hood, we recommend that the hood should not be ﬁtted below 65cm (for electric)

or (70cm for gas) the measurements taken from the surface of the cooking appliance to the underside of the cooker hood.

• It is a possible ﬁre risk if the hood is not sited as recommended.

• To ensure the best results, the cooking fumes should be able to rise naturally towards the inlet grilles on the underside of

the cooker hood and the cooker hood should be positioned away from doors and windows, which will create turbulence.

• Ducting

• If the room where the hood is to be used contains a fuel-burning appliance such as a central heating boiler then its ﬂue

must be of the room sealed or balanced ﬂue type.

• If other types of ﬂue or appliances are ﬁtted ensure that there is an adequate supply of fresh air to the room. Ensure the

kitchen is ﬁtted with an airbrick, which should have a cross-sectional measurement equivalent to the diameter of the ducting

being ﬁtted, if not larger.

• The ducting system for this cooker hood must not be connected to any existing ventilation system, which is being used for

any other purposes or to a mechanically controlled ventilation ducting.

• The ducting used must be made from ﬁre retardant materials and the correct diameter must be used, as incorrect sized

ducting will affect the performance of this cooker hood.

• When the cooker hood is used in conjunction with other appliances supplied with energy other than electricity, the negative

pressure in the room must not exceed 0.04 mbar to prevent the fumes from combustion being drawn back into the room.

• The appliance is for domestic use only and should not be operated by children or people who are inﬁrm without supervi

sion.

• This appliance must be positioned so that the wall socket is accessible.

3 FITTING

Any permanent electrical installation must comply with the latest regulations concerning this type of installation and a qualiﬁed

electrician must carry out the work. Non-compliance could cause serious accidents or injury and would deem the manufacturers

guarantee null and void.

IMPORTANT - The wires in this mains lead are coloured in accordance with the following code :

green / yellow : earth blue : neutral brown : live

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the

terminals in your plug, proceed as follows.

- The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter

E or by the earth symbol or coloured green or green and yellow.

- The wire which is coloured blue must be connected to the terminal which is marked with the letter

N or coloured black.

- The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

1) Draw a vertical line up the wall from the centre of the cooking appliance below as illustrated in ﬁg. 4 - item 1.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Boretti PRO 100 IX in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 5,99 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Boretti PRO 100 IX Manual

Product: