714380
21
Zoom out
Zoom in
Previous page
1/28
Next page
EN
21
Operation
www.bora.com
6 Operation
Observe all safety and warning information during
operation (see the Safety section).
INFO The cooktop may only be operated when
the stainless steel grease filter of the
cooktop extractor is installed (see operating
in structions for cooktop extractor).
INFO Clean the cooking zone before using the
cooktop for the first time (see the Cleaning
chapter).
6.1 Switching cooktop on/off
Fig. 6.1 Push and pull control knob
6.1.1 Switching on the cooking zone
Push and turn the control knob to power level
1
to switch on the cooking zone.
The operating indicator light is active.
Adjusting the power level
Turn the control knob to the desired power level.
6.1.2 Switching on the power setting
INFO Both cooking zones are equipped with a
power-enhancing power setting.
If the front cooking zone is operated at power setting
P
,
the other cooking zones can be operated at a maximum
power level of
6
.
If the back cooking zone is operated at power setting
P
,
the other cooking zones can be operated at a maximum
power level of
8
.
If the power level of the other cooking zone increases
above this level, the power setting will be switched back
to
P
.
Press and turn the control knob past power level
9
until the power setting
P
is shown on the cooking zone
indicator.
After 10 minutes, the cooking zone is automatically
switched back to power level
9
.
6.1.3 Switching the power setting off early
Turn the control knob past power level
9
again.
Power level
9
is active and is shown in the cooking
zone indicator.
or
Turn the control knob to the desired power level.
The power level set is active and is shown in the
cooking zone indicator.
6.1.4 Switching off the cooking zone
INFO If a cooking zone indicator shows
H
,
the cooking zone is still hot.
INFO Turn the cooking zone off after use.
Do not rely on the pan size recognition.
Turn the control knob to power level
0
to switch off
the cooking zone.
The operating indicator light is inactive.
The cooktop is switched off when there are no longer
any active cooking zones.
Pay attention to the residual heat display (see the
Device Description chapter).
6.1.5 Automatic heat up function
Switching on the automatic heat up function
Press and turn the control knob for the desired cooking
zone to the left to the symbol
A
.
Within 5 seconds, select the desired power level
(continuous cooking stage), which should be used
to continue the cooking session after the end of the
automatic heat up function.
The cooking zone indicator will display the symbol
A
to show that the automatic heat up function is
activated as well as the continuous cooking stage
set, for example
5
.
An
A
will be displayed in the cooking zone indicator
while the automatic heat up function is active.
Once the automatic heat up period has passed, the
power will be reduced to the selected continuous
cooking stage.
If a higher continuous cooking stage is selected while
the automatic heat up function is active, the new time
will automatically be valid.
Switching off the automatic heat up function
The activated automatic heat up function will end
pre maturely if you
reduce the power level (continuous cooking stage).
set power level
9
.
activate the power setting
P
.
activate the heat retention level
v
.
switch off the cooktop.
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bora PI11 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bora PI11 in the language / languages: English as an attachment in your email.

The manual is 1,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bora PI11

Bora PI11 User Manual - German - 28 pages

Bora PI11 User Manual - Dutch - 28 pages

Bora PI11 User Manual - French - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info