714380
19
Zoom out
Zoom in
Previous page
1/28
Next page
EN
19
Installation
www.bora.com
Connecting the cooktop and the control box
Create the connection between the cooktop and the
control box.
Firstly connect the yellow/green earthing cable to the
indicated point on the control box.
Earthing symbol
Now connect the multi-pin, colour-coded plugs on the
relevant cooking zone to the corresponding colour-
coded sockets on the control box.
5.6 Power connection
Observe all safety and warning information
(see the Safety chapter).
Observe all national and regional laws and regulations
as well as the supplementary regulations of the local
utility companies.
INFO The power connection may only be established
by a certified specialist. He/she also assumes
responsibility for the proper installation and
commissioning.
The power supply line for use (pre-assembled) must be at
least Type H05VV-F or H05VVH2-F.
Cross-section: 3G1.5 mm² with 1-phase connection
If the connection line has been damaged this must be
replaced by a special connection line. This may only
be done by an authorized member of the After Sales
Service team.
Establishing the power connection
Switch off the main switch/automatic circuit breaker
before connecting the cooktop.
Protect the main switch/automatic circuit breaker
from being switched on without permission.
Make sure the device is not energised.
Only connect the cooktop using a permanent
connection to a power supply cable.
1
L1
2
N PE
220 - 240 V~
Fig. 5.17 Connection diagram 1-phase
Create the connection between the cooktop and the
control box.
Verify that the installation was done correctly.
Switch on the main switch/automatic circuit breaker.
Put the cooktop into operation (see the Operation
section).
Check all the functions are working correctly.
1
2
Fig. 5.15 Cooktop and height adjustment plates
[1] Cooktop
[2] Height adjustment plates
If applicable, insert the height adjustment plate [2].
2
1
Fig. 5.16 Mounting brackets
[1] Screw
[1] Mounting bracket
Fasten the cooktop [1] using the mounting brackets
[2].
Tighten the mounting bracket screws [1] with max.
10 Nm.
Verify that the alignment is correct.
Seal the devices with black heat-resistant silicone
sealing compound after the installation work is
completed.
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bora PI11 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bora PI11 in the language / languages: English as an attachment in your email.

The manual is 1,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bora PI11

Bora PI11 User Manual - German - 28 pages

Bora PI11 User Manual - Dutch - 28 pages

Bora PI11 User Manual - French - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info