476989

Bompani BO690 Manual

14
Zoom out
Zoom in
Previous page
1/60
Next page
14
- Ignite the burner at maximum flame;
- pull off the knob, without using a lever against the control panel,
which might be damaged;
- access the by-pass with a small screwdriver and back off by about
3 turns (turning the screwdriver anti-clockwise);
- turn the tap rod anti-clockwise again until it stops: the burner will
be at maximum flame;
- screw the by-pass slowly back in, without pushing the screw-
driver, until the flame has apparently shrunk to 1/4 of the maximum
size, checking that it is sufficiently stable even in quite strong
draughts.
SETTING OVEN BURNER MINIMUM LEVELS
If the cooker is to work on bottled gas (butane/propane), the ther-
mostat by-pass must be screwed right down.If the cooker is to work
on natural gas, proceed as follows:
- Remove the oven bottom (push towards the back and raise);
- ignite the oven burner, turning the knob pointer to the maximum
setting;
- shut the oven door;
- access the thermostat by-pass ( fig. 9);
- back off the thermostat by-pass by about 3 turns;
- after 5 or 6 minutes, turn the knob pointer to the minimum set-
ting;
- slowly re-tighten the by-pass, watching the flame decrease in size
through the window in the closed oven door until the tongue of the
flame is about 4 mm long. Never keep the flame too low. It must
be stable even when the oven door is opened or closed quickly;
- turn off the burner and replace the oven bottom.
CONNECTING TO THE ELECTRICAL MAINS
Before making the connection, check that:
- the mains voltage is as indicated on the nameplate;
- the earth connection is in good working order.
For direct connection to a power mains, a device that ensures discon-
nection from the mains must be installed, with a opening distance
for the contacts that allows for a complete disconnection under
conditions of category III electrical overload, in conformity with the
installation instructions.
If the appliance power lead is not fitted with a plug, use an approved
standard type, remembering that:
- the green-yellow wire must be used for the earth connection;
- the blue wire is the neutral;
- the brown wire is live;
- the lead must never touch hot surfaces over about 75 degrees
C;
- replacement leads must be of type HO5RR-F of suitable size (see
diagrams in fig. 2).
- if the appliance is supplied without lead, using type HO5RR-F cable
of suitable size (see diagrams in fig. 2).
IMPORTANT: the manufacturer declines all liability for damage due
to failure to comply with the regulations and standards in force. Check
that the appliance is correctly connected to the earth (see diagrams
in fig. 2 at the back of the manual).
FOR COOKERS WITH ELECTRIC IGNITION
The correct gaps between the electrode and the burner are shown
in figures 7a,7b.
If no spark is generated, do not keep on trying as this might damage
the generator.
Possible causes of malfunctions:
- spark plug damp, dirty or broken;
- electrode-burner gap not correct;
- spark plug wire broken or without sheathing;
- spark discharging to earth (to other parts of the cooker);
- generator or microswitch damaged;
- air has built up in the pipes (particularly if the cooker has been out
of use for a long time);
- air-gas mixture incorrect (poor fuel setting).
THE SAFETY DEVICE
The correct gap between the end of the thermocouple sensor and
the burner is shown in figures 7a,7b.
To check that the valve is working properly, proceed as follows:
- ignite the burner and leave it to work for about 3 minutes;
- turn off the burner by returning the knob to off position ( );
- after 90 seconds for hob burners, 60 seconds for oven and grill
burners, turn the knob pointer to the "on" position;
- release the knob in this position and move a burning match towards
the burner; IT MUST NOT IGNITE.
Time needed to excite the magnet during ignition: 10 seconds ap-
prox.Automatic tripping time, after flame has been turned off: not
more than 90 seconds for hob burners; not more than 60 seconds
for oven and grill burners.
IMPORTANT:
- Before doing any work inside the cooker, disconnect the mains
plug and shut the gas tap.
- Never use matches to check the gas circuit for leaks. If a specific
control device is not available, foam or very soapy water can be
used.
- When re-closing the hob, check that the electrical wires of the spark
plugs (if present) are not close to the injectors, so that they cannot
run across them.
Installation
GB
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bompani BO690 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bompani BO690 in the language / languages: English, French, Italian, Spanish as an attachment in your email.

The manual is 1,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info