552044
17
Zoom out
Zoom in
Previous page
1/24
Next page
17
Ensure that your mains power corresponds with
the specifications of the appliance. The specifica-
tions are printed on the rating label.
Connect the mains cable to a properly installed
and earthed wall outlet.
If the plug after installation is not accessible, a
corresponding disconnect device must be availa-
ble to meet the relevant safety regulations.
Reverse the
Reverse the Reverse the
Reverse the door o
door odoor o
door opening
peningpening
pening
If required, the door opening can be moved from the
right (supplied condition) to the left side.
WARNING:
WARNING:WARNING:
WARNING:
When replacing the door stop, the appliance must be
disconnected from the power supply. Always unplug
the appliance first.
NOTE
NOTENOTE
NOTE:
::
:
When installing, ask another person to assist.
You possibly need:
screw wrench, Phillips screw-
driver as well as a thin-blade screwdriver.
Dismount the upper limit plate incl. hinge pin by
loosening the screws. Open the door a little and
take it carefully off the lower door hinge. Place the
door on a padded surface to prevent it from
scratches.
Tilt the appliance slightly backwards and block it
in this position. Loosen the lower hinge pin and
put it in the opposite bracket.
Replace the appliance upright again. Insert the
appliance door on the lower hinge pin and fix the
door to the property position.
Attach the upper limit plate after you have un-
screwed the hinge pin and used it on the other
side of the plate. Insert the hinge pin in the hole of
the appliance door and tight the plate.
Check if the door is arranged vertical as well as
horizontal, so that a smooth opening and closing
of the door is ensured.
Built
BuiltBuilt
Built-
--
-in
inin
in
Built-in openings
Height x Width x Depth
872–880 x
560–570 x 550 mm
Figures in mm
For the appropriate venting an exhaust duct of
approx. 50 mm depth is to provide at the appliance
back.
The ventilation openings in the furniture base and
building must be min. 200 cm
2
to ensure that heated
air can freely escape.
Install the power cord so that the appli-
ance can be easily connected after
installation. Slide the appliance into the
build-in opening until the stop plate (A)
abuts the furniture.
Press the rubber seal between the
appliance and built-in furniture firmly
(on the side without hinge).
Open the appliance door. Push the
appliance side, which is located oppo-
site the hinges, against the built-in
furniture. Arrange the appliance for a
secure, vertical position, fix it with the
supplied screws and put the protective
cap (B) on.
Separate the parts b, c and d of part a.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bomann VSE 228.1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bomann VSE 228.1 in the language / languages: English as an attachment in your email.

The manual is 0,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bomann VSE 228.1

Bomann VSE 228.1 User Manual - German - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info