814356
22
Zoom out
Zoom in
Previous page
1/24
Next page
22
Cleaning / replacing the door seal
Regularly check the seal for dirt, damage and air
tightness!
Checking the seal for air tightness
Clamp a thin piece of paper at various points for
testing. The paper must be equally difficult to pull
through at all points.
Cleaning the gasket
Clean the gasket with clear water only!
CAUTION, grease and oil makes the seal porous
and brittle. Wipe up grease or oil immediately with
a damp, clean cloth.
Replacing the seal
Remove the contents of the appliance and, if nec-
essary, defrost the unit. Pay attention to how the
old gasket is attached. Most gaskets are only
plugged in.
Remove the worn gasket rubber by removing it
from the groove. Carefully clean the appliance
door and the groove below the rubber and remove
any adhesive residue.
Attach the new rubber. If necessary, heat the rub-
ber seal with a hair dryer or hot water and shape it
by hand. Start pressing the gasket in one corner
and then press it around the door into the groove
provided for this purpose.
Continue to check the seal regularly for dirt and
damage!
Defrosting
CAUTION:
Never use metal objects (e.g. knifes) to remove ice
from the evaporator. Otherwise, it can be damaged.
To achieve better cooling and to save energy, defrost
the appliance regularly:
To initiate the defrosting process, disconnect the
appliance from the power supply.
Remove the contents of the appliance and store
everything covered in a cool place.
Once the ice has melted, wipe up the condensa-
tion and dry the inside of the appliance.
Then you can put the appliance back into opera-
tion by connecting it to the power supply and ad-
justing the temperature control.
Changing the light
CAUTION:
Do NOT remove the cover of the light. The LED light
may be replaced / repaired in case of failure / defect
only by an authorized specialist.
Replacing the door hinge
If the appliance door starts to stutter, crack or jam
when you open it, it is probably due to a worn or
damaged hinge.
It is recommended to replace all door hinges at the
same time, otherwise the next repair will soon be
beckoning.
Remove the contents of the appliance and the
movable interior parts.
Tilt the appliance backwards and block it in this
position to prevent the door from sliding out.
Loosen the hinge cover, as described under
“Re-
versing the door opening”
and disassemble the
upper door hinge.
Turn out the stand and disassemble the lower
door hinge.
The respective hinge assembly is carried out in
reverse order.
Open and close the appliance door for a test run,
readjust the hinges if necessary. In any case,
make sure that the door fits tightly and accurately.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bomann KSG 7286 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bomann KSG 7286 in the language / languages: English, German as an attachment in your email.

The manual is 0.66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info