552039
6
Zoom out
Zoom in
Previous page
1/16
Next page
6
10/2013
I
NSTALLATION
Location
Sufficient ventilation around the device is necessary in order for the heat to dissipate properly and to
guarantee efficient cooling operation at low power consumption. For this purpose, leave sufficient
space around the device. Please also refer to chapter “Built-in“.
- Minimum clearance of 5 cm between rear side and wall,
- at least 1 cm on both sides.
- Leave proper space in front of the device in order to open the door at an angle of 160°.
IMPORTANT:
- Do not expose the device to direct sunlight.
- Do not place near heaters, next to a stove or any other heat sources.
- Only install at a location with an ambient temperature suitable for the climate class of the device.
For information on the climate class, please refer to chapter “Specifications“ or to the rating label
located in the interior or on the rear side of the device.
- Do not use the device outdoors.
- Avoid installation at locations with high humidity (e.g. outdoors, bathroom), as metal parts would be
susceptible to corrosion under such circumstances.
- Do not place the device near volatile or combustible materials (e.g. gas, fuel, alcohol, paint, etc.)
and in rooms which may have poor air circulation (e.g. garages).
Electrical connection
The kind of current (AC) and the voltage must be conform to the data of the rating label, located inside
or outside on the back of the unit. In case of heavy voltage fluctuations, it is recommended to use an
automatic alternating current regulator.
The plug, together with the grounding conductor, must fit into the wall socket. The mains plug must be
freely accessible.
Mains cable
- Do not extend or roll up the cable during operation.
- Also, the cable must not be near the compressor on the rear side, since latter one gets hot during
operation. In case of any contact, the isolation would be damaged resulting in electric leakage.
- The use of extension cables is not recommended.
- Do not connect the device to the mains with wet hands.
- Install the device for the wall socket to be freely accessible.
R
EVERSE
T
HE
D
OOR
O
PENING
If required, the door opening can be moved from the right (supplied condition) to the left side.
WARNING: When replacing the door stop, the device must be disconnected from the power sup-
ply. Always unplug the device first.
- Tilt the device slightly backwards and block it in this position in order to avoid the slipping out of the
door.
- Dismount the upper stop plate and the underlying door hinge by loosening the screws.
- Take the door carefully down and place the door on a padded surface to prevent it from scratches.
- Unscrew the lower brackets and mount them each on the corresponding opposite sides.
- Replace the device upright again. Put the door on the lower hinge pin and fix the door to its proper-
ty position.
- Attach the upper door hinge to the corresponding opposite side and mount the stop plate again by
using the screws.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bomann KSE 327 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bomann KSE 327 in the language / languages: English as an attachment in your email.

The manual is 0,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bomann KSE 327

Bomann KSE 327 User Manual - German - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info