651992
6
Zoom out
Zoom in
Previous page
1/16
Next page
Preparing the worktop for
Preparing the worktop for Preparing the worktop for
Preparing the worktop for
installation of the hob
installation of the hobinstallation of the hob
installation of the hob
CAUTION:
CAUTION:CAUTION:
CAUTION:
Before cutting secure the outer
cutout
adhesive tape to avoid traces of jigsaw on the
top.
The worktop must have a
minimum thickness of
30 mm, it
must lie horizontally and be sealed to
the wall side against overflowing liquids or moi
ture.
The cut surfaces (cutout e
dges) must be sealed
with special varnish, silicone rubber or cast raisin
in order to p
revent swelling caused by humidity.
Clean and dry the worktop in the cutout area
thoroughly.
Worktop cutout
Worktop cutoutWorktop cutout
Worktop cutout
Prepare the cutout of the worktop
according to the
dimensional drawing.
Figures in mm
Installing the hob
Installing the hobInstalling the hob
Installing the hob
1
11
1
2
22
2
3
33
3
4
44
4
First check the factory fitted hob seal
frame to the integrity and the proper fit.
Put the hob with the connecting cable
with
the control panel to the front into the pr
pared cutout.
Make sure that the distances to the cutting a
equal on all four sides and that the seal is resting
on the worktop.
Fix the hob depending on the worktop thickness
by attaching the enclosed
brackets (3)
6
installation of the hob
installation of the hobinstallation of the hob
installation of the hob
cutout
edge with wide
adhesive tape to avoid traces of jigsaw on the
work-
minimum thickness of
must lie horizontally and be sealed to
the wall side against overflowing liquids or moi
s-
dges) must be sealed
with special varnish, silicone rubber or cast raisin
revent swelling caused by humidity.
Clean and dry the worktop in the cutout area
according to the
Hob
Gasket
Bracket
Screw
First check the factory fitted hob seal
at the hob
frame to the integrity and the proper fit.
Put the hob with the connecting cable
first and
the control panel to the front into the pr
e-
Make sure that the distances to the cutting a
re
equal on all four sides and that the seal is resting
Fix the hob depending on the worktop thickness
brackets (3)
from the
hob bottom at the provided holes and fasten them
with the screws (4).
Electrical connect
Electrical connectElectrical connect
Electrical connection
ionion
ion
Information for the
Information for the Information for the
Information for the
authorized expert
authorized expertauthorized expert
authorized expert
WARNING:
WARNING:WARNING:
WARNING:
The installation to the mains supply must conform
to the local standards and regulations.
Connecting the appliance to a domestic power
socket or using multiple sockets or extension c
bles is not permitted.
Improper connection may cause to an
shock
shockshock
shock!
Before connecting, ensure that the power supply
corresponds with the information on the rating l
bel (appliance bottom
) an
Fix the mains cable in the tension relief.
The electric
al installation must have an isolation
device which lets you disconnect the appliance at
all poles from the power supply.
device shall be executed with a contact width of
min. 3 mm.
Arrange the mains cable in such a way that it
does not get
in contact with any hot components
of the appliance. Do not lead it over sharp edges
or corners.
Mains socket
Mains socketMains socket
Mains socket
The socket must be connected according to the
standards to a single-
pole circuit breaker. The co
nection is shown below:
NOTE
NOTENOTE
NOTE:
: :
:
L1
L1L1
L1-brown L2
L2L2
L2-black P3
P3P3
P3-green
-
hob bottom at the provided holes and fasten them
authorized expert
authorized expertauthorized expert
authorized expert
The installation to the mains supply must conform
to the local standards and regulations.
Connecting the appliance to a domestic power
socket or using multiple sockets or extension c
a-
Improper connection may cause to an
electric
electric electric
electric
Before connecting, ensure that the power supply
corresponds with the information on the rating l
a-
) an
d the wiring diagram.
Fix the mains cable in the tension relief.
al installation must have an isolation
device which lets you disconnect the appliance at
all poles from the power supply.
The disconnect
device shall be executed with a contact width of
Arrange the mains cable in such a way that it
in contact with any hot components
of the appliance. Do not lead it over sharp edges
The socket must be connected according to the
pole circuit breaker. The co
n-
-
yellow N1
N1N1
N1-blue N2
N2N2
N2-grey
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bomann EBK 960 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bomann EBK 960 in the language / languages: English as an attachment in your email.

The manual is 0,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bomann EBK 960

Bomann EBK 960 User Manual - German - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info