651975
20
Zoom out
Zoom in
Previous page
1/28
Next page
Place the outer duct with the
fixed
parallel to the other rails (1+2).
Slide the inner (upper) duct along the slide fixture into the outer (lower) duct. Make sure that the inner duct
is aligned with the vents at the top.
duct or sliding back into the outer duct.
For extraction mode, correctly position the flexible
Pull the inner duct cover up a
nd
screwing in the plate screws (8)
(Fig. G)
I
II
Installing the activated carbo
nstalling the activated carbonstalling the activated carbo
nstalling the activated carbo
n filter for recirculation mode
n filter for recirculation moden filter for recirculation mode
n filter for recirculation mode
Remove the alumin
um grease filter.
Place the carbon filter onto the air intake of the extraction duct. Make sure that the mounting pins on the
extraction duct engage the mounting slots of the carbon filter. Turn the respective filter clockwise until it
clicks into place.
Reinstall the alumin
um grease filter
NOTE
NOTENOTE
NOTE:
::
:
The activated carbon filter absorbs
odours
Electrical connection
Electrical connectionElectrical connection
Electrical connection
WARNING:
WARNING:WARNING:
WARNING:
The installation to the mains supply must conform to the local standards
Improper connection may cause to an
Do not modify the appliance
plug
an authorized specialist.
The accessibility of the power plug must be ens
supply in case of an emergency.
Ensure that your mains power corresponds with the specifications of the appliance. The specifications are
printed on the rating label.
Connect the mains cable to a
properly installed and earthed wall outlet.
The
extractor hood is operated via pushbuttons.
switched on and off with the
corresponding
Lowest fan setting
Moderate fan setting
20
fixed
rail (3) onto the extr
actor hood (Fig. F). Fasten the rail (3) to the wall
is aligned with the vents at the top.
Determine the exte
nsion length of the duct cover by pulling up the inner
duct or sliding back into the outer duct.
For extraction mode, correctly position the flexible
extraction hose (not supplied).
nd
fasten the duct unit on the side to the
previously
(Fig. G)
.
n filter for recirculation mode
n filter for recirculation moden filter for recirculation mode
n filter for recirculation mode
um grease filter.
um grease filter
.
odours
and must be replaced at least every six
months
The installation to the mains supply must conform to the local standards
and regulations.
Improper connection may cause to an
electric shoc
electric shocelectric shoc
electric shock!
k!k!
k!
plug
. If the plug does not fit properly to the outlet, let install a proper outlet by
The accessibility of the power plug must be ens
ured in order to disconnect the
appliance
properly installed and earthed wall outlet.
Startup / Operation
Startup / OperationStartup / Operation
Startup / Operation
extractor hood is operated via pushbuttons.
The individual fan settings as
well
corresponding
buttons.
Highest fan setting
Lighting
actor hood (Fig. F). Fasten the rail (3) to the wall
Slide the inner (upper) duct along the slide fixture into the outer (lower) duct. Make sure that the inner duct
nsion length of the duct cover by pulling up the inner
previously
mounted rail (2) by
Place the carbon filter onto the air intake of the extraction duct. Make sure that the mounting pins on the
extraction duct engage the mounting slots of the carbon filter. Turn the respective filter clockwise until it
months
regardless of use.
and regulations.
. If the plug does not fit properly to the outlet, let install a proper outlet by
appliance
from the power
Ensure that your mains power corresponds with the specifications of the appliance. The specifications are
well
as the lighting can be
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bomann DU 657 G at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bomann DU 657 G in the language / languages: English, German as an attachment in your email.

The manual is 1,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info