651970
19
Zoom out
Zoom in
Previous page
1/28
Next page
Assembly
AssemblyAssembly
Assembly
WARNING:
WARNING:WARNING:
WARNING:
When assembling or inserting
the
be connected to the mains.
Failure to use the mounting fixtures may lead to a
CAUTION
CAUTIONCAUTION
CAUTION:
::
:
Before mounting,
check that the wall
When drilling the holes in the wall always make sure that no existing electrical cables or other objects are
damaged.
Make sure that the vents are clear of obstacles and are not covered.
NOTE
NOTENOTE
NOTE:
::
:
Recomm
RecommRecomm
Recomm
endations for preparation work
endations for preparation workendations for preparation work
endations for preparation work
When installing, ask another
person
Wear protective gloves to prevent injuries from any sharp edges.
1
11
1
2
22
2
Mounting at the wall
The hood is mounted
at the wall or
centrally above the hob in
conformance
Remove the grease filter grid or aluminum grease filter (depending on the model).
Select the fume outlet and set
the lever to the appropriate position, see “Selecting the fume outlet”.
Mounting at the wall
Mounting at the wallMounting at the wall
Mounting at the wall
Mark the
necessary holes for the wall mounting by using the supplied drill template and check them with a
spirit level.
Drill two
mounting holes Ø 8 mm into the wall and insert the dowel pins (1). Then rotate the mounting
screws (2) as far as these stick out about 4 mm from the wall.
Suspend the hood and tighten the screws through the hood body. Check the secure fitting and
position.
Mounting below the wall u
Mounting below the wall uMounting below the wall u
Mounting below the wall unit
nitnit
nit
Hold the hood
to the specified cabinet position and draw the drilling points from the inside of the unit corr
sponding to the four screw holes. Check them with a spirit level.
19
the
extraction filter as well as the carbon filter
mat
Failure to use the mounting fixtures may lead to a
risk of electric shock
risk of electric shockrisk of electric shock
risk of electric shock.
check that the wall
or wall unit has sufficient load capacity to
bear
When drilling the holes in the wall always make sure that no existing electrical cables or other objects are
Make sure that the vents are clear of obstacles and are not covered.
endations for preparation work
endations for preparation workendations for preparation work
endations for preparation work
person
to assist.
Wear protective gloves to prevent injuries from any sharp edges.
3
33
3
4
44
4
5
55
5
Mounting below the wall unit
at the wall or
below a suitable wall unit. Determine the
position
conformance
with the specified safety distances.
Remove the grease filter grid or aluminum grease filter (depending on the model).
the lever to the appropriate position, see “Selecting the fume outlet”.
necessary holes for the wall mounting by using the supplied drill template and check them with a
mounting holes Ø 8 mm into the wall and insert the dowel pins (1). Then rotate the mounting
screws (2) as far as these stick out about 4 mm from the wall.
Suspend the hood and tighten the screws through the hood body. Check the secure fitting and
to the specified cabinet position and draw the drilling points from the inside of the unit corr
sponding to the four screw holes. Check them with a spirit level.
mat
, the appliance must not
bear
the extractor hood.
When drilling the holes in the wall always make sure that no existing electrical cables or other objects are
6
66
6
position
of the extractor hood
the lever to the appropriate position, see “Selecting the fume outlet”.
necessary holes for the wall mounting by using the supplied drill template and check them with a
mounting holes Ø 8 mm into the wall and insert the dowel pins (1). Then rotate the mounting
Suspend the hood and tighten the screws through the hood body. Check the secure fitting and
horizontally
to the specified cabinet position and draw the drilling points from the inside of the unit corr
e-
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bomann DU 622.1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bomann DU 622.1 in the language / languages: English, German as an attachment in your email.

The manual is 1,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info