Manual Bomann cb 2002 (page 24 of 54) (English, German, Dutch, Italian)

361458

Zoom out

Zoom in

1/54

ENGLISH

5. When the brew group is correctly inserted, close the

service door.

Note: Only if the service door can be closed easily

is the brew group correctly in position.

Should this not be the case please proceed as

described under points 7 to 11.

6. Turn the machine off by the I/O switch (5) and then

back on again. The machine is ready to use.

7. If it is still not possible to insert the brew group,

check whether it is in the correct starting position.

This is the case if the distance of 10 mm (see dia-

gram B) is maintained.

8. Turn the brew group until you can see the coupling of

the spindle (diagram A).

9. Attach the upper section of the adjustment tool to

the coupling of the spindle on the ﬂ oor of the brew

group.

10. Twist the spindle until the distance of 10 mm (dia-

gram B) is reached. Correct the direction of rotation if

necessary. Ensure that the arrow of the brew group is

located within the start marking.

11. In order to turn the drive shaft on the ﬂ oor of the ser-

vice chamber, place the underside of the adjustment

tool (socket wrench) on the drive shaft and turn it

either slowly to the left or to the right.

Note: It is essential that the coupling of the brew

group meshes with the drive shaft on the ﬂ oor of the

service chamber.

Cleaning the Coffee Powder Container

Open the service door (6) and remove the brew group.

Then open the ﬁ lling hole (18). Please use the brush

to clean the chamber (see diagram). Then remove the

coffee residues from the service chamber.

Cleaning the Coffee Grounds Collector

• Remove the coffee grounds collector (8).

• Remove the coffee grounds.

• Clean the coffee grounds collector under running

water.

• Reinstall the container.

The machine only works when the coffee grounds collec-

tor is correctly installed.

Emptying and Cleaning the Drip Collector

Empty and clean the drip collector (10) regularly,

especially when it is full. This is shown by the red ﬁ lling

level indicator (11) in the middle of the drip collector

protruding upwards.

• Pull out the drip collector.

• Remove the drip collector cover (11).

• Clean the collector and the collector cover under

running water.

• Reinstall the drip collector cover on the collector.

• Replace the drip collector.

Descaling

Important: Regular descaling protects the machine

from expensive repairs. Damage resulting from a lack

of regular cleaning, incorrect use or non-compliance

with the instructions is not covered by the guarantee.

Descaling serves the purpose of removing all lime

deposits from the surfaces and all openings through

which water ﬂ ows. This ensures that the valves, heating

elements and other important components will work

correctly.

In order to ensure that it functions correctly the machine

must be descaled regularly.

Note: Please use a descaling agent for household

equipment.

Please do not use any vinegar, but rather a commer-

cially available descaling agent on a citric acid base.

For the correct quantities please see the instructions.

It is possible to read off how much water has ﬂ owed

through the machine before descaling. To this purpose it

is necessary to switch to the programming mode.

• Keep the MENU/OK/MEMORY button pressed

down for ﬁ ve seconds.

• Press the MENU/OK/MEMORY button repeatedly

until the word “Reﬁ ll” appears in the display.

• Count the arrowhead pairs. Each pair signiﬁ es 1/14

of the permitted water ﬂ ow.

Note: If the hot water/steam switch (9) is opened un-

der this menu item the descaling programme starts.

The device is equipped with an internal monitoring sys-

tem which shows when the machine is switched on that

the descaling procedure should be started. In this case

the “Reﬁ ll” and “Recover” symbols ﬂ ash alternately in

the display. The machine is still on standby.

In order to descale the machine, please proceed as

follows:

• Place a vessel with a capacity of more than 1l under

the hot water/steam nozzle (14) (the drip collector

(10) must be inserted).

• Fill the water tank (4) with the prepared descaling

agent. Keep the MENU/OK/MEMORY button

pressed for ﬁ ve seconds.

• Press the MENU/OK/MEMORY button repeatedly

until the word “Reﬁ ll” appears in the display.

• Start the descaling process by opening the hot

water/steam switch (9).

Drive Shaft

05-KAV 2936 GB 24 03.12.2004, 12:13:31 Uhr

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bomann cb 2002 in the language / languages: English, German, Dutch, Italian as an attachment in your email.

The manual is 7,79 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bomann cb 2002 Manual

Product: