361458

Bomann cb 2002 Manual

23
Zoom out
Zoom in
Previous page
1/54
Next page
ENGLISH
23
Cleaning the Brew Group
Before cleaning the device switch it to the „O“
position and then remove the mains plug (19) from
the socket.
If the machine is used daily the brew group must be
cleaned regularly, i.e. at least once a week. Only warm
water should be used for cleaning.
• Allow the machine to cool down.
• Open the service door (6).
• Lift the brew group slightly and then carefully pull it
out horizontally.
• Rinse the brew group thoroughly with warm water.
• Allow the brew group to dry.
• Clean the service chamber with a damp cloth.
• Reinstall the brew group horizontally until it locks in
place.
• Close the service door.
Note: Only if the service door can be closed easily is
the brew group correctly in position.
Removing/Inserting the Brew Group
In order to remove the brew group please switch the
machine off and open the service door (6). Grip the brew
group by the handle (diagram A). Lift the brew group
slightly and then remove it from the housing. To reinsert
the brew group proceed in the reverse order (diagram B).
Cleaning the Filter Screens
Cleaning the Lower Filter Screen
If after a certain time the
coffee comes out of the
machine too slowly, or if
no coffee comes out, this
may be due to the fact
that the coffee that has
been used is too rich. In
this case you should open
the service door (6) and
remove the brew group. In diagram A the lower screen
is clearly visible. The brush of the measuring spoon can
be used to clean the screen. Any residues adhering to
the screen can be removed by gently moving the brush.
If the openings in the screen are still blocked you can
remove the screen from its retaining device. In order to
remove the screen please proceed as follows:
• Release the screw of the screen with an appropriate
cool.
• Remove the screen from its retaining mechanism.
• Hold the fi lter up to the light and check which fi lter
openings are blocked. Clean the openings with the
point of a needle if necessary.
• Now replace the cleaned screen in its retaining me-
chanism.
• Reposition the screw and gently tighten it.
Cleaning the Upper Filter Screen
The upper screen
becomes visible when
the brew group is rotated
- see diagram B. In order
to clean the screen please
proceed as described
above. Please note that
the upper screen is slight-
ly offset and its removal
requires a little dexterity.
Adjusting the Position of the Drive Shaft
If it is not possible to close the service door (6), check
whether the brew group has been correctly reinstalled.
Note: the drive shaft of the brew group must fi t onto the
drive shaft of the motor. Should this not be the case,
please proceed as follows:
1. Turn the machine off by the I/O switch (5). Open the
service door (6).
2. Remove the brew group from the service chamber
and close the service door. Turn the machine on with
the I/O switch.
3. The drive shaft is now readjusted. This procedure
lasts approximately 20 seconds.
4. Then open the service door and try to insert the brew
group again.
Brew Group Underside
Spindle Coupling
Adjustment Tool
Spindle Coupling
05-KAV 2936 GB 23 03.12.2004, 12:13:30 Uhr
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bomann cb 2002 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bomann cb 2002 in the language / languages: English, German, Dutch, Italian as an attachment in your email.

The manual is 7,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info