Manual Blomberg WM 67120 NBL00 (page 13 of 40) (English)

640549

Zoom out

Zoom in

1/40

13 EN

kinks or cuts on it.

WARNING - Drain hose outlet must

not contact the drained water.

Drain hose may be connected into

a sink, into the drain of a sink, to a

standpipe and floor drain.

• Whenconnectingintoasink,the

drain hose should be placed at the

edge of the sink and secured with

the hose guide supplied by the

manufacturer. Additionally, the guided

hose may be tied to the water faucet

with a strap for extra security.

• Drainhosemaybeconnectedinto

the drain of a sink . Be sure that the

connection is safe and not leaking.

An additional clip etc can be used for

safe connection.

• Drainhosemayalsobeconnectedto

a minimum 1.26 in (32 mm) diameter

stand pipe.

• Besuretosecurethedrainhose

tightly to the pipe (stand pipe, drain

pipe/edge of the sink) with a strap

etc.

• Thehoseshouldbeplacedbetween

16 and 39 in. (40 and 100 cm) from

the floor level

• Ifyouhavefloordrainsystem,you

can place the drain hose in the hole

located on the floor.

Installation Checklist

• Waterinlethosesandaccessory

bags must be removed from the

wash drum.

• Transportation/shippingboltsmust

be removed.

• Washermustbeproperlyleveledby

using the adjustable feet.

• Waterinlethosesareconnected

water pressure of 145 psi (10 bar) at

maximum. If the pressure is higher than

145 psi, a pressure-reducing valve must

be installed before the water inlet. If the

water pressure is lower than 15 psi (1

bar), water fill time may extend or water

inlet valve may shut off completely.

• Hotwatersupplytemperaturemust

notexceed140˚F(60˚C).

• Donotconnectthewashertoan

unpressurized water boiler since

water pressure may not be adequate

for proper operation.

• Donotremovethefilterslocated

on the water supply hoses (on

faucet/hose and hose/inlet valve

connections).

• Alwaysusegenuine“Blomberg”

water supply hoses when connecting

with this washer. Old or worn-out

hoses must not be reused. It is

not advised to extend inlet or drain

hoses, if necessary consult your

dealer or technical service about

hose extensions.

• Hotandcoldwaterfaucetsmust

always be easily accessible to the

user.

• Attheendofawashingday,turnoff

water faucets to prevent any leakage

or water damage that may occur due

to a faulty condition of the appliance.

• Checktheapplianceandinlethose

connections for water leakage after

each use. If there is leakage, turn off

the appliance and water faucets and

call service.

• Checkthewaterinletanddrainhose

connections regularly for any leakage.

Hoses should be replaced every 5

years.

• Ifthereisnohotwatersupply,hot

water valve must be connected to a

cold water faucet nevertheless. Both

water valves should be connected to

water supply for proper operation of

your washer.

Drainage

WARNING - Drain hose should not

be bent. Be sure that there are no

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Blomberg WM 67120 NBL00 in the language / languages: English as an attachment in your email.

The manual is 1,23 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Blomberg WM 67120 NBL00 Manual

Product: