Manual Black Decker SMS254 T1 (page 12 of 140) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

578656

Zoom out

Zoom in

1/140

ENGLISH

Warning! Always position the workpiece against the fence.

Any piece that is bowed or warped and cannot be held flat

on the table or against fence may trap the blade and should

not be used.

Pullover cut (fig. J & K)

Warning! Never pull the cutting head assembly and rotating

blade toward you during the cut. The blade may try to climb

up on the top of the workpiece causing the cutting head

assembly and spinning blade to kick back. Never lower the

rotating saw blade down before pulling the cutting head to

the front of the saw.

 Unlock the carriage (29) with the lock knob (48) and

allow the cutting head assembly to move freely (fig. J).

 Move the cutting head to the required mitre angle and

bevel angle in accordance with the mitre cut and bevel

cut procedures.

 Hold the main operating handle (2) and pull the carriage

(29) forward until the centre of the saw blade is over the

front of the workpiece.

 Operate the on/off switch (3) and press the saw arm

release lever (36) to lower the cutting head.

 When the saw reaches full speed, push the main

operating handle (2) down slowly, cutting through the

leading edge of the workpiece.

 Slowly move the main operating handle (2) toward the

fence to complete the cut.

 Release the on/off switch (3) and allow the blade to stop

before allowing the cutting head to rise.

Chop cut

 Slide the cutting head to the rear position as far as it will

go, and lock the carriage (29) with the lock knob (48).

 Operate the on/off switch (3) and press the saw arm

release lever (36) to lower the cutting head.

 When the saw reaches full speed, push the main

operating handle (2) down slowly, cutting through the

workpiece.

 Release the on/off switch (3) and allow the blade to stop

before allowing the cutting head to rise.

Mitre cut

 Switch the laser on/off switch (1) to on.

 Loosen the mitre detent lever (11) and move the table to

the required angle. There are preset stops at 0°, 15°,

22.5°, 31.6°, and 45°. Tighten the mitre detent

lever (11).

 For any other angle use the Superlok

mitre clamp (9)

(fig. B) to set the mitre to the required angle.

 Operate the on/off switch (3), then press the saw arm

release lever (36) and lower the cutting head.

 When the saw reaches full speed, push the main

operating handle (2) down slowly, cutting through the

workpiece.

 Release the on/off switch (3) and allow the blade to stop

before allowing the cutting head to rise.

Operating the high sliding fence for all bevel and

compound mitre cuts

 The moveable part of the left side of the fence can be

adjusted to provide maximum support of the work piece

near the blade, while allowing the saw to bevel to a full

47° left. The sliding distance is limited by stops in both

directions.

Adjusting the fence (fig. E)

 Loosen the high sliding fence clamp (20) and slide the

fence to the left.

 Make a dry run with the saw switched off and check for

clearance.

 Adjust the fence to be as close to the blade as practical

to provide maximum work piece support, without

interfering with the up and down movement of the arm.

 Tighten the high sliding fence clamp (20) to secure the

fence in place.

Warning! The guide groove can become clogged with

sawdust. Use a stick or low pressure air to clear the guide

groove.

Bevel cut

 Make sure that the high sliding fence is adjusted to the

correct orientation before adjusting the bevel angle.

Note: The saw is fitted with a special 33.9° bevel pin (23) for

special crown moulding.

 Loosen the bevel lock handle (30) (fig. F) and move the

cutting head to the required angle. Tighten the bevel

lock handle (30).

 Operate the on/off switch, then press the release lever

(36) when the saw reaches full speed, push the main

operating handle (2) down slowly, cutting through the

workpiece.

 Release the on/off switch (3) and allow the blade to stop

before allowing the cutting head to rise.

Make sure that the arm is securely locked when bevelling.

Compound cut

 Make sure that the high sliding fence is adjusted to the

correct orientation before adjusting the bevel angle to

make a compound cut.

A compound cut is a combination of mitre cut and bevel cut.

 Switch the laser on/off switch (1) to on.

 Refer to the above procedures to perform this cut.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker SMS254 T1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,64 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker SMS254 T1

Black Decker SMS254 T1 User Manual - English - 20 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker SMS254 T1 Manual

Product: