578656

Black Decker SMS254 T1 Manual

13
Zoom out
Zoom in
Previous page
1/140
Next page
13
ENGLISH
Release the on/off switch (3) and allow the blade to stop
before allowing the cutting head to rise.
Base moulding cut
Base moulding can be cut vertical against the fence or flat on
the table.
Refer to the following table:
Crown moulding cut (fig. L)
Crown moulding can only be cut flat on the table with this
mitre saw.
This mitre saw has special mitre stops on 31.6° left and
right and a bevel stop of 33.9° for special crown
moulding, i.e. 52° between the back of the moulding and
the top flat surface that fits against the ceiling; 38°
between the back of the moulding and the bottom flat
surface that fits against the wall.
Refer to the following table to make this crown moulding
cut:
Note: . These special stops can not be used with 45° crown
moulding.
Note: Since most rooms do not have angles of exactly 90°,
fine tuning is needed, always make a test cut to confirm the
correct angles.
Setting the cutting depth (fig. M)
The depth of cut can be preset for even and repetitive
shallow cuts.
Adjust the cutting head down until the teeth of the blade
are at the required depth of cut.
While holding the upper arm in position, turn the stop
knob (47) until it touches the stop plate (49).
Check the blade depth by moving the cutting head front
to back through the full motion of a typical cut along the
control arm.
Carrying the tool (fig. N)
Loosen the mitre detent lever (11) (fig. B) and turn the
table all the way to the right. Lock the table at the 45°
mitre angle.
Pull the cutting head to the front of the saw and lock the
carriage with the lock knob (48) (fig. J).
Lower the cutting head and push in the lock pin (46)
(fig. H).
Carry the mitre saw with the front and the rear carrying
handles (24, 27).
Settings Vertical position
(back of moulding
is against the
fence)
Horizontal position
(back of moulding is
flat on the table)
Bevel angle 0° 45°
Moulding position Left side Right
side
Left side Right
side
Inside
corner
Mitre
angle
Left at
45°
Right at
45°
0° 0°
Moulding
position
Bottom
against
table
Bottom
against
table
Top
against
fence
Bottom
against
fence
Finished
side
Keep left
side of
cut
Keep
right side
of cut
Keep left
side of
cut
Keep left
side of
cut
Outside
corner
Mitre
angle
Right at
45°
Left at
45°
0° 0°
Moulding
position
Bottom
against
table
Bottom
against
table
Top
against
fence
Bottom
against
fence
Finished
side
Keep left
side of
cut
Keep
right side
of cut
Keep
right side
of cut
Keep
right side
of cut
Settings Left side Right side
Inside
corner
Mitre
angle
Right 31.6° 31.6° left
Bevel
angle
33.9° 33.9°
Moulding
position
Top against fence Bottom against
fence
Finished
side
Keep left side of cut Keep left side of cut
Outside
corner
Mitre
angle
Right 31.6° Left 31.6°
Bevel
angle
33.9° 33.9°
Moulding
position
Bottom against
fence
Top against fence
Finished
side
Keep right side of
cut
Keep right side of
cut
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker SMS254 T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker SMS254 T1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker SMS254 T1

Black Decker SMS254 T1 User Manual - English - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info