381455

Black Decker pp 360 Manual

6
Zoom out
Zoom in
Previous page
1/84
Next page
6
ENGLISH
(Original instructions)
The charger may hum and become warm while charging;
this is normal and does not indicate a problem.
Generally, a charging time of 8 hours will enable the tool to
operate at an effective power level for most tasks. However,
further charging for up to 10 hours could signicantly increase
the run time, depending on the battery and charging conditions.
Warning! Do not charge the battery at ambient temperatures
below 4 °C or above 40 °C.
Selecting the direction of rotation
For tightening screws, use forward (clockwise) rotation. For
loosening screws use reverse (counterclockwise) rotation.
u To select forward rotation, push the forward/reverse slider
(2) to the left.
u To select reverse rotation, push the forward/reverse slider
(2) to the right.
u To lock the tool, set the forward/reverse button into the
centre position.
Screwdriving
u Select forward or reverse rotation using the forward/
reverse slider (2).
u To switch the tool on, press the on/off switch switch (1).
u To switch the tool off, release the on/off switch (1).
Spindle lock
This tool is tted with a spindle lock so that it can be used as a
normal screwdriver. Use the tool this way to loosen very tight
screws or to rmly tighten screws.
Rotating the gearbox (g. C, D & E)
The tool is tted with a rotating gearbox to facilitate various
screwdriving applications, such as reaching screws in tight
corners and close to ceilings and oors. The bitholder can be
set to a centre position and 3 off-centre positions: top, left and
right. The gearbox and the spindle can be rotated to set the
various bitholder positions.
u To rotate the gearbox (10) push the pivot release slider (5)
forward and turn the gearbox 90° to the left or to the right
(g. C & D). Note: The gearbox will only turn 90° left and
right. Do not attempt to turn any further.
u To rotate the spindle (11) push the pivot release slider (5)
backward and turn the spindle head 180° left or right (g. E).
Warning! Ensure the gearbox and spindle are locked into
place before use.
LED light
The LED light is activated automatically when the trigger is
depressed. The LED will illuminate when the trigger is partially
depressed, before the unit begins running. The LED will also
illuminate when the trigger is depressed and the forward/
reverse slider (2) is in the locked off position (central position).
Hints for optimum use
u Let the tool work at its own pace. Do not overload.
u Always use the correct type and size of screwdriver bit.
u If screws are difcult to tighten, try applying a small
amount of washing liquid or soap as a lubricant.
u Use the auto spindle lock to loosen very tight screws or to
rmly tighten screws.
u Always hold the tool and screwdriver bit in a straight line
with the screw.
u When screwing in wood, it is recommended to drill a pilot
hole with a depth equal to the length of the screw. A pilot
hole guides the screw and prevents splintering or
distortion of the wood. For the optimum size of the pilot
hole, refer to the table below.
u When screwing in hardwood, also drill a clearance hole
with a depth equal to half the length of the screw. For the
optimum size of the clearance hole, refer to the table
below.
Screw size Pilot hole ø Pilot hole ø Clearance
(softwood) (hardwood) hole
No. 6 (3.5 mm) 2.0 mm 2.5 mm 4 mm
No. 8 (4 mm) 3.2 mm 3.5 mm 5.0 mm
No. 10 (5 mm) 3.5 mm 4.0 mm 5.7 mm
Accessories
The performance of your tool depends on the accessory used.
Black & Decker and Piranha accessories are engineered to
high quality standards and designed to enhance the
performance of your tool. By using these accessories you will
get the very best from your tool.
This tool uses screwdriver bits with a 1/4" (6.35 mm)
hexagonal shank.
Maintenance
Your Black & Decker tool has been designed to operate over a
long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker pp 360 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker pp 360 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info