381455
5
Zoom out
Zoom in
Previous page
1/84
Next page
5
ENGLISH
(Original instructions)
Labels on tool
The following pictograms are shown on the tool:
:
Warning! To reduce the risk of injury, the user must
read the instruction manual.
Additional safety instructions for batteries and
chargers
Batteries
u Never attempt to open for any reason.
u Do not expose the battery to water.
u Do not expose the battery to heat.
u Do not store in locations where the temperature may
exceed 40 °C.
u Charge only at ambient temperatures between
10 °C and 40 °C.
u Charge only using the charger provided with the tool.
u When disposing of batteries, follow the instructions given
in the section "Protecting the environment".
Chargers
u Use your Black & Decker charger only to charge the
battery in the tool with which it was supplied. Other
batteries could burst, causing personal injury and damage.
u Never attempt to charge non-rechargeable batteries.
u Have defective cords replaced immediately.
u Do not expose the charger to water.
u Do not open the charger.
u Do not probe the charger.
$
The charger is intended for indoor use only.
+
Read the instruction manual before use.
-
The charger automatically shuts off if the ambient
temperature becomes too high. As soon as the
ambient temperature has cooled down, the charger
will resume operating.
j
Charge only at ambient temperatures between
10 °C and 40 °C.
y
Charging
Electrical safety
#
Your charger is double insulated; therefore no earth
wire is required. Always check that the mains
voltage corresponds to the voltage on the rating
plate. Never attempt to replace the charger unit with
a regular mains plug.
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Overview
1. On/off switch
2. Forward/reverse slider
3. LED light
4. Bit holder
5. Pivot release slider
Fig. A
6. Charger
7. Charger connector
8. Charging indicator
9. Charging base
Assembly
Fitting and removing a screwdriver bit (g. B)
This tool uses screwdriver bits with a 1/4" (6.35 mm)
hexagonal shank.
u To t a bit, insert the bit shaft into the bit holder (4).
u To remove a bit, pull the bit shaft out of the bit holder (4).
Use
u Before rst use, the battery must be charged for 14 hours.
u The battery needs to be charged before rst use and
whenever it fails to produce sufcient power on jobs that
were easily done before. When charging the battery for
the rst time, or after a prolonged storage, it will only
accept an 80% charge. After several charges and
discharge cycles, the battery will attain full capacity.
u Place the tool on the charging base whenever it is not in use.
Charging the battery (g. A)
u Place the tool on the charging base (9).
u Insert the connector (7) into the charging base.
u Plug in the charger (6).
u Leave the tool connected to the charger for 8 - 10 hours.
The red light illuminates when the unit is on charge and will
stay red as long as there is power to the charger. The red light
will not go off to indicate a full charge.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker pp 360 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker pp 360 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info