Manual Black Decker PF128 (page 7 of 88) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

473007

Zoom out

Zoom in

1/88

ENGLISH

Using the 3 hr charger

u To charge the battery (7), remove it from the tool and slide

the charger receptacle (9) onto the battery.

u Plug in the charger (8).

The battery will become warm while charging. After approx.

3 hours of charging, the battery will be sufciently charged for

use in regular applications. After approx. 6 hours of charging,

the battery will be fully charged.

u Remove the charger receptacle from the battery.

Using the 1hr charger

u To charge the battery (7), remove it from the tool and

insert it into the charger (9). The battery will only t into

the charger in one way. Do not force. Be sure that the

battery is fully seated in the charger.

u Plug in the charger.

u Check if the charging indicator (10) is red. If the charging

indicator lights up green, the battery is either fully charged

or too hot and cannot be charged. If this happens, remove

the battery from the charger, let the battery cool down for

approx. 1 hour and re-insert it.

After approx. 1 hour of charging, the charging indicator (10)

will change colour from red to green. The battery is now fully

charged.

u Remove the battery from the charger.

Selectingthedirectionofrotation(g.E)

For drilling and for tightening screws, use forward (clockwise)

rotation. For loosening screws or removing a jammed drill bit,

use reverse (counterclockwise) rotation.

u To select forward rotation, push the forward/reverse slider

(2) to the left.

u To select reverse rotation, push the forward/reverse slider

to the right.

u To lock the tool, set the forward/reverse slider into the

centre position.

Selectingtheoperatingmodeortorque(g.F)

This tool is tted with a collar to select the operating mode and

to set the torque for tightening screws. Large screws and hard

workpiece materials require a higher torque setting than small

screws and soft workpiece materials. The collar has a wide

range of settings to suit your application.

u For drilling in wood, metal and plastics, set the collar (4) to

the drilling position by aligning the symbol with the

marking (16).

u For screwdriving, set the collar to the desired setting. If you

do not yet know the appropriate setting, proceed as follows:

- Set the collar (4) to the lowest torque setting.

- Tighten the rst screw.

- If the clutch ratchets before the desired result is

achieved, increase the collar setting and continue

tightening the screw. Repeat until you reach the correct

setting. Use this setting for the remaining screws.

Drillinginmasonry(g.F&G)

u For drilling in masonry, set the collar (4) to the hammer

drilling position by aligning the symbol with the marking

(16).

u Slide the two-gear selector (5) towards the front of the tool

(2nd gear).

Two-gearselector(g.G)

u For drilling in steel and for screwdriving applications, slide

the two-gear selector (5) towards the rear of the tool

(1st gear).

u For drilling in materials other than steel, slide the two-gear

selector (5) towards the front of the tool (2nd gear).

Drilling/screwdriving

u Select forward or reverse rotation using the forward/

reverse slider (2).

u To switch the tool on, press the switch (1). The tool speed

depends on how far you press the switch.

u To switch the tool off, release the switch.

Hints for optimum use

Drilling

u Always apply a light pressure in a straight line with the drill

bit.

u Just before the drill tip breaks through the other side of the

workpiece, decrease pressure on the tool.

u Use a block of wood to back up workpieces that may splinter.

u Use spade bits when drilling large diameter holes in wood.

u Use HSS drill bits when drilling in metal.

u Use masonry bits when drilling in soft masonry.

u Use a lubricant when drilling metals other than cast iron

and brass.

u Make an indentation using a centre punch at the centre of

the hole to be drilled in order to improve accuracy.

Screwdriving

u Always use the correct type and size of screwdriver bit.

u If screws are difcult to tighten, try applying a small

amount of washing liquid or soap as a lubricant.

u Always hold the tool and screwdriver bit in a straight line

with the screw.

Maintenance

Your Black & Decker tool has been designed to operate over

a long period of time with a minimum of maintenance.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker PF128 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,35 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker PF128 Manual

Product: