473007

Black Decker PF128 Manual

6
Zoom out
Zoom in
Previous page
1/88
Next page
6
ENGLISH
u Charge only at ambient temperatures between 10 °C and
40 °C.
u Charge only using the charger provided with the tool.
u When disposing of batteries, follow the instructions given
in the section "Protecting the environment".
Chargers
u Use your Black & Decker charger only to charge the
battery in the tool with which it was supplied. Other
batteries could burst, causing personal injury and damage.
u Never attempt to charge non-rechargeable batteries.
u Have defective cords replaced immediately.
u Do not expose the charger to water.
u Do not open the charger.
u Do not probe the charger.
$
The charger is intended for indoor use only.
+
Read the instruction manual before use.
j
Charge only at ambient temperatures between
10 °C and 40 °C.
U
Charging process completed
y
Charging
Electrical safety
#
Your charger is double insulated; therefore no earth
wire is required. Always check that the mains
voltage corresponds to the voltage on the rating
plate. Never attempt to replace the charger unit with
a regular mains plug.
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Forward/reverse slider
3. Chuck
4. Mode selector / torque adjustment collar
5. Two-gear selector
6. Bit holder
7. Battery
Fig. A
8. Charger
9. Charger receptacle
10. Charging indicator
Assembly
Warning! Before assembly, remove the battery from the tool.
Fittingandremovingthebattery(g.B)
u To t the battery (7), line it up with the receptacle on the
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
u To remove the battery, push the release button (12) while
at the same time pulling the battery out of the receptacle.
Fittingthebatterycap(g.C)
Warning! Fit the cap (13) to the battery (7) for transportation
and storage.
Fitting and removing a drill bit or screwdriver bit
(g.D)
This tool is tted with a keyless chuck to allow for an easy
exchange of bits.
u Lock the tool by setting the forward/reverse slider (2) to
the centre position.
u Open the chuck by turning the sleeve (14) with one hand
while holding the tool with the other.
u Insert the bit shaft (15) into the chuck.
u Firmly tighten the chuck by turning sleeve (14) with one
hand while holding the tool with the other.
This tool is supplied with a double-ended screwdriver bit in the
bit holder (6).
u To remove the screwdriver bit from the bit holder, lift the bit
from the recess.
u To store the screwdriver bit, rmly push it into the holder.
Use
Warning! Let the tool work at its own pace. Do not overload.
Chargingthebattery(g.A)
The battery needs to be charged before rst use and
whenever it fails to produce sufcient power on jobs that were
easily done before. When charging the battery for the rst
time, or after prolonged storage, it will only accept an 80%
charge. After several charge and discharge cycles, the battery
will attain full capacity. The battery may become warm while
charging; this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging
temperature: approx. 24 °C.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker PF128 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker PF128 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info