427189

Black Decker kw 1600 eka Manual

10
Zoom out
Zoom in
Previous page
1/96
Next page
10
ENGLISH
Use
Warning! Let the tool work at its own pace. Do not overload.
u Carefully guide the cable in order to avoid accidentally
cutting it.
Adjustingthedepthofcut(g.I,J&K)
The depth of cut is the distance X between the depth stop bar
(9) and the depth stop (29). The depth of cut can be set in two
different ways as described below.
Adjustingthedepthofcutusingthescale(g.J)
u Fit the router bit as described above.
u Loosen the locking screw (30).
u Pull the plunge lock lever (5) up.
u Plunge the router down until the router bit touches the
workpiece.
u Push the plunge lock lever (5) down.
u Move the depth stop bar (9) down against the depth stop
using the depth stop adjuster (31). Reset the scale by
aligning the zero marking (32) with the arrow (33).
u Move the depth stop bar (9) to the calculated position
using the depth stop adjuster (31). One quarter turn
corresponds to approx. 6.25 mm.
u Tighten the locking screw (30).
u Fine adjust using the adjusting knob (34). One full turn
corresponds to approx. 1 mm.
u Pull the plunge lock lever (5) up and return the router to its
original position.
u After switching the router on, plunge it down and make the
desired cut.
Adjustingthedepthofcutusingapieceofwood(g.K)
u Fit the router bit and plunge the router down as described
above.
u Loosen the locking screw (30).
u Move the depth stop bar (9) up using the depth stop
adjuster (31).
u Place a piece of wood with a thickness equal to the
desired depth of cut between the depth stop (29) and the
depth stop bar (9).
u Move the depth stop bar (9) down against the wood using
the depth stop adjuster (31).
u Tighten the locking screw (30).
u Fine adjust using the adjusting knob (34).
u Remove the piece of wood.
u Pull the plunge lock lever (5) up and return the router to its
original position.
u After switching the router on, plunge it down and make the
desired cut.
Adjustingtherevolverdepthstop(g.L)
After turning the revolver depth stop to the desired setting, you
can ne-adjust the depth stop to be used. If you want to make
several cuts with a different depth of cut, adjust each of the
depth stops.
u Turn the depth stop screw (35) up or down as required
using a screwdriver.
Setting the speed
u Set the speed control knob (4) to the required speed.
Use a high speed for small diameter router bits. Use a low
speed for large diameter router bits.
Usingabattenasaguide(g.M)
When it is not possible to use the edge guide, for example
when routing grooves in the back panel of a bookcase to
support shelves, proceed as follows:
u Select a piece of wood with a straight edge to use as a
batten.
u Place the batten onto the workpiece.
u Move the batten until it is in the correct position to guide
the tool.
u Securely clamp the batten to the workpiece.
Usingthetemplateguide(g.D)
The template guide can be used to make a cutout shape from
a template, for instance a letter.
u Secure the template over the workpiece with double-sided
tape or ‘G' clamps.
u The router bit must extend below the ange of the
template guide, to cut the workpiece in the shape of the
template.
Usingthedistancepiece(g.E)
The distance piece can be used for trimming wooden or
laminate vertical projections.
Usingthecentringpin(g.F)
The centring pin can be used to cut out circular patterns.
u Drill a hole for the point of the centring pin in the centre of
the circle to be cut.
u Place the router on the workpiece with the point of the
centring pin in the drilled hole.
u Adjust the radius of the circle with the bars of the edge
guide.
u The router can now be moved over the workpiece to cut
out the circle.
Usingthecopyfollower(g.G)
The copy follower helps to maintain an equal cutting distance
along the edge of irregularly shaped workpieces.
u Place the router on the workpiece at the desired distance
from the edge to be copied.
u Adjust the bars of the edge guide until the wheel is in
contact with the workpiece.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker kw 1600 eka at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker kw 1600 eka in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info