581128
6
Zoom out
Zoom in
Previous page
1/60
Next page
6
ENGLISH
Fit the edge guide shoe (17) in the same way as the
normal shoe.
Note 1: The cross bar (18) can be fitted in two ways:
Fit the cross bar with the sides up for circle cutting.
Fit the cross bar with the sides down for ripping.
Note 2: The guide arm (19) can be mounted on either side of
the shoe (fig. E).
Remove the screw (20).
Rotate the guide arm 180° and refit it on the other side of
the shoe.
Secure the guide arm with the screw, using the other hole
(21).
Use
Setting the cutting speed (fig. F)
Set the speed control wheel (3) to the required speed
range (1 = low speed, 6 = high speed).
Use a high speed for wood, a medium speed for
aluminium, ceramics and PVC and a low speed for metals
other than aluminium.
Note: After using the saw for extended periods on low speeds,
run the saw on high speed for 3 minutes to aid cooling.
Switching on and off (fig. G)
To switch the tool on, press the lock-off button (2) and
squeeze the on/off switch (1).
To switch the tool off, release the on/off switch.
Cutting circles (fig. D & H)
The circle guide can be used to saw out circular patterns.
Fit the circle guide for circle cutting.
The guide arm (19) is marked to allow you to set the cross
bar (18) to the radius of the circle to be cut.
Loosen the knob (22) and slide the cross bar over the
guide arm to the desired position.
Tighten the knob.
Drill a small hole for the point of the pivot knob in the
centre of the circle to be cut.
Drill a second hole where the saw blade will be
positionend or cut inwards from the edge of the
workpiece to get the sawblade into position.
Saw out the circle in a counterclockwise direction. Note:
Left-handed users should saw in a clockwise direction.
Using the edge guide (fig. D & I)
The edge guide can be used to maintain an equal cutting
distance when ripping.
Fit the edge guide for ripping.
Loosen the knob (22) and slide the cross bar (18) over the
guide arm (19) to the desired position.
Tighten the knob.
Keep the cross bar pressed firmly against the straight
edge of the workpiece during sawing.
Hints for optimum use
Sawing laminates
As the saw blade cuts on the upward stroke, splintering may
occur on the surface closest to the shoe plate.
Use a fine-tooth saw blade.
Saw from the back surface of the workpiece.
To minimise splintering, clamp a piece of scrap wood or
hardboard to both sides of the workpiece and saw
through this sandwich.
Sawing metal
Be aware that sawing metal takes much more time than
sawing wood.
Use a saw blade suitable for sawing metal. Use a fine-
tooth saw blade for ferrous metals and a coarser saw
blade for nonferrous metals.
When cutting thin sheet metal, clamp a piece of scrap
wood to the back surface of the workpiece and cut
through this sandwich.
Spread a film of oil along the intended line of cut.
Cutting branches
Branches up to 25 mm in diameter can be cut with this tool.
Warning! Do not use the tool while in a tree, on a ladder or
on any other unstable surface. Be aware of where the branch
will fall.
Cut downward and away from your body.
Make the cut close to the main branch or tree body.
Accessories
The performance of your tool depends on the accessory used.
Black & Decker and Piranha accessories are engineered to
high quality standards and designed to enhance the
performance of your tool. By using these accessories you will
get the very best from your tool.
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Protecting the environment
Black & Decker provides a facility for recycling
Black & Decker products once they have reached the
end of their working life. This service is provided
free of charge.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker KS990EK T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KS990EK T1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info