580991
6
Zoom out
Zoom in
Previous page
1/72
Next page
6
ENGLISH
Vibration
The declared vibration emission values stated
in the technical data and the declaration of
conformity have been measured in accordance
with a standard test method provided by EN 60745
and may be used for comparing one tool with
another. The declared vibration emission value
may also be used in a preliminary assessment of
exposure.
Warning! The vibration emission value during
actual use of the power tool can differ from the
declared value depending on the ways in which
the tool is used. The vibration level may increase
above the level stated.
When assessing vibration exposure to determine
safety measures required by 2002/44/EC to
protect persons regularly using power tools in
employment, an estimation of vibration exposure
should consider, the actual conditions of use and
the way the tool is used, including taking account
of all parts of the operating cycle such as the
times when the tool is switched off and when it is
running idle in addition to the trigger time.
Labels on tools
Warning! To reduce the risk of injury, the
user must read the instruction manual.
Electrical safety
This tool is double insulated; therefore
no earth wire is required. Always check
that the power supply corresponds to the
voltage on the rating plate.
This appliance is not intended for use by
young or in rm persons without supervision.
Children must be supervised to ensure they
do not play with the appliance.
If the supply cord is damaged, it must be
replaced by the manufacturer or an authorised
Black & Decker Service Centre in order to
avoid a hazard.
Features
1. Lock-on button
2. Variable speed on/off switch
3. Blade storage compartment cover
4. Shoe plate
5. Blade support roller
6. Tool-free blade clamp
Assembly
Warning! Before attempting any of the following
operations, make sure that the tool is switched
off and unplugged and that the saw blade has
stopped. Used saw blades may be hot.
Fitting the saw blade ( g. A)
Hold the saw blade (7) as shown, with the
teeth facing forward.
Push and hold the blade clamp (6) down.
Insert the shank of the saw blade into the
blade holder (8) as far as it will go.
Release the blade clamp (6).
Saw blade storage ( g. B)
Saw blades (7) can be stored in the storage
compartment located on the side of the tool.
Open the cover (3) of the saw blade storage
compartment by holding the tab on the top of
the cover (3) and pulling it outward.
The blades are retained in the compartment
by a magnetic strip. To remove a blade, press
down on one end of the blade to raise the
other end, and remove.
Close the cover (3) of the saw blade storage
compartment and make sure that it is latched
closed.
Warning! Close the compartment door securely
before operating the saw.
Residual risks
Additional residual risks may arise when using the
tool which may not be included in the enclosed
safety warnings. These risks can arise from
misuse, prolonged use etc.
Even with the application of the relevant safety
regulations and the implementation of safety
devices, certain residual risks cannot be avoided.
These include:
Injuries caused by touching any rotating/
moving parts.
Injuries caused when changing any parts,
blades or accessories.
Injuries caused by prolonged use of a tool.
When using any tool for prolonged periods
make sure you take regular breaks.
Impairment of hearing.
Health hazards caused by breathing dust
developed when using your tool (example:-
working with wood, especially oak, beech and
MDF).
Use
Adjusting the shoe plate for bevel cuts ( g. C)
The shoe plate (4) can be set to make either
a straight cut or a left or right bevel cut at an angle
of 45°.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker KS777 T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KS777 T1 in the language / languages: Polish, Turkish as an attachment in your email.

The manual is 2,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker KS777 T1

Black Decker KS777 T1 Quick start guide - English - 12 pages

Black Decker KS777 T1 User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info