578204
9
Zoom out
Zoom in
Previous page
1/96
Next page
9
ENGLISH
Labels on tool
Warning! To reduce the risk of injury, the
user must read the instruction manual.
Wear safety glasses or goggles when
operating this tool.
Wear ear protection when operating this
tool.
Electrical safety
This tool is double insulated; therefore no
earth wire is required. Always check that the
power supply corresponds to the voltage on
the rating plate.
If the supply cord is damaged, it must be re-
placed by the manufacturer or an authorised
Black & Decker Service Centre in order to avoid
a hazard.
Features
Your tool has some or all of the following features:
1. On/off switch
2. Side handle
3. Spindle lock
4. Guard
Assembly
Warning! Before assembly, make sure that the tool
is switched off and unplugged.
Fitting and removing the guard ( g. A & B)
The tool is supplied with a guard intended for
grinding purposes only. If the unit is intended to
perform cutting off operations, a guard speci c for
this operation must be tted. A suitable guard for
cutting off operations part number 1004484-00 is
available and can be obtained from Black & Decker
service centres.
Fitting
Place the tool on a table, with the spindle (5)
facing up.
Place the spring washer (6) over the spindle and
locate it on the shoulder (7).
Place the guard (4) onto the tool as shown.
Place the ange (8) over the spindle with the
protruding pips towards the guard. Make sure
that the holes in the ange align with the screw
holes.
Secure the ange with the screws (9). Make sure
that the screws are fully tight and that the guard
can be rotated.
Removing
Use a screwdriver to remove the screws (9).
Remove the ange (8), guard (4) and spring
washer (7).
Store these parts carefully.
Warning! Never use the tool without the guard.
Fitting the side handle
Screw the side handle (2) into one of the mount-
ing holes in the tool.
Warning! Always use the side handle.
Fitting and removing grinding or cutting
discs ( g. C - E)
Always use the correct type of disc for your
application.
Always use discs with the correct diameter and bore
size (see technical data).
Fitting
Fit the guard as described above.
Place the inner ange (10) onto the spindle (5) as
shown ( g. C). Make sure that the ange is cor-
rectly located on the at sides of the spindle.
Place the disc (11) onto the spindle (5) as shown
( g. C).
If the disc has a raised centre (12), make sure
that the raised centre faces the inner ange.
Make sure that the disc locates correctly on the
inner ange.
Place the outer ange (13) onto the spindle.
When tting a grinding disc, the raised centre on
the outer ange must face towards the disc (A
in g. D). When tting a cutting disc, the raised
centre on the outer ange must face away from
the disc (B in g. D).
Keep the spindle lock (3) depressed and tighten
the outer ange using the two-pin spanner (14)
( g. E).
Removing
Keep the spindle lock (3) depressed and loosen
the outer ange (13) using the two-pin spanner
(14) ( g. E).
Remove the outer ange (13) and the disc (11).
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker KG915 T3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KG915 T3 in the language / languages: English, German, French as an attachment in your email.

The manual is 4,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker KG915 T3

Black Decker KG915 T3 Quick start guide - English - 16 pages

Black Decker KG915 T3 User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 112 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info