Manual Black Decker KG915 T3 (page 8 of 96) (English, German, French)

578204

Zoom out

Zoom in

1/96

ENGLISH

Additional safety warnings specific for

abrasive cutting-off operations

 Do not “jam” the cut-off wheel or apply ex-

cessive pressure. Do not attempt to make

an excessive depth of cut. Over stressing the

wheel increases the loading and susceptibility

to twisting or binding of the wheel in the cut and

the possibility of kickback or wheel breakage.

 Do not position your body in line with and

behind the rotating wheel. When the wheel, at

the point of operation, is moving away from your

body, the possible kickback may propel the spin-

ning wheel and the power tool directly at you.

 When wheel is binding or when interrupting

a cut for any reason, switch off the power

tool and hold the power tool motionless

until the wheel comes to a complete stop.

Never attempt to remove the cut-off wheel

from the cut while the wheel is in motion

otherwise kickback may occur. Investigate

and take corrective action to eliminate the cause

of wheel binding.

 Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed

and carefully re-enter the cut. The wheel

may bind, walk up or kickback if the power tool

is restarted in the workpiece.

 Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kick-

back. Large workpieces tend to sag under their

own weight. Supports must be placed under the

workpiece near the line of cut and near the edge

of the workpiece on both sides of the wheel.

 Use extra caution when making a “pocket

cut” into existing walls or other blind areas.

The protruding wheel may cut gas or water

pipes, electrical wiring or objects that can cause

kickback.

Safety warnings specific for sanding

operations

 Do not use excessively oversized sanding

disc paper.

Follow manufacturers recommendations,

when selecting sanding paper. Larger sand-

ing paper extending beyond the sanding pad

presents a laceration hazard and may cause

snagging, tearing of the disc or kickback.

Safety warnings specific for polishing

operations

 Do not allow any loose portion of the polish-

ing bonnet or its attachment strings to spin

freely. Tuck away or trim any loose attach-

ment strings. Loose and spinning attachment

strings can entangle your ﬁ ngers or snag on the

workpiece.

Safety warnings speciﬁ c for wire brushing

operations

 Be aware that wire bristles are thrown by

the brush even during ordinary operation.

Do not overstress the wires by applying

excessive load to the brush. The wire bristles

can easily penetrate light clothing and/or skin.

 If the use of a guard is recommended for wire

brushing, do not allow any interference of

the wire wheel or brush with the guard. Wire

wheel or brush may expand in diameter due to

work load and centrifugal forces.

Safety of others

 This appliance is not intended for use by persons

(including children) with reduced physical, sen-

sory or mental capabilities, or lack of experience

and knowledge, unless they have been given

supervision or instruction concerning use of

the appliance by a person responsible for their

safety.

 Children should be supervised to ensure that

they do not play with the appliance.

Vibration

The declared vibration emission values stated in

the technical data and the declaration of conformity

have been measured in accordance with a standard

test method provided by EN 60745 and may be used

for comparing one tool with another. The declared

vibration emission value may also be used in

a preliminary assessment of exposure.

Warning! The vibration emission value during actual

use of the power tool can differ from the declared

value depending on the ways in which the tool is

used. The vibration level may increase above the

level stated.

When assessing vibration exposure to determine

safety measures required by 2002/44/EC to protect

persons regularly using power tools in employment,

an estimation of vibration exposure should consider,

the actual conditions of use and the way the tool is

used, including taking account of all parts of the

operating cycle such as the times when the tool is

switched off and when it is running idle in addition

to the trigger time.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KG915 T3 in the language / languages: English, German, French as an attachment in your email.

The manual is 4,05 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker KG915 T3

Black Decker KG915 T3 Quick start guide - English - 16 pages

Black Decker KG915 T3 User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 112 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker KG915 T3 Manual

Product: