381442
10
Zoom out
Zoom in
Previous page
1/104
Next page
10
ENGLISH
To charge the battery, set the
tool to the straight position
and insert the charger plug
(10) into the connector (11).
Plug in the charger. Switch on
at the mains.
Leave the tool connected to the
charger for at least 12 hours.
The tool can be left connected to
the charger indefinitely.
The charger may hum and become
warm while charging; this is normal
and does not indicate a problem.
Before using the tool, unplug
the charger and disconnect
the tool from the charger.
Do not use the tool while it
is connected to the charger.
Adjusting the handle (fig. D)
For optimum versatility, the
handle can be set to different
positions.
Press the handle adjustment
button (4).
Swivel the handle into the
desired position.
Release the button.
KC9036 - Manual spindle lock
(fig. E)
The manual spindle lock allows
you to use the tool as a regular
screwdriver. You can give an
extra twist to firmly tighten a
screw or to loosen a very tight
screw.
To activate the spindle lock,
turn the collar (2) to the
symbol. With the spindle lock
activated, the tool cannot be
switched on.
To release the spindle lock,
turn the collar (2) to the
symbol.
KC9039 - Setting the torque
(fig. E)
This tool is fitted with a collar to
set the torque for tightening
screws.
Large screws and hard workpiece
materials require a higher torque
setting than small screws and soft
workpiece materials. The collar
has a wide range of settings to
suit your application.
Turn the collar (2) to the
desired setting. If you do not
yet know the appropriate
setting, proceed as follows:
- Set the collar to the lowest
torque setting.
- Tighten the first screw.
- If the clutch ratchets before
the desired result is achieved,
increase the collar setting and
continue tightening the
screw. Repeat until you reach
the correct setting. Use this
setting for the remaining
screws.
Operating the tool (fig. F)
Make sure that the spindle
lock is released.
To tighten a screw or nut,
slide the on/off switch (1) to
the right and press it.
To loosen a screw or nut,
slide the on/off switch (1) to
the left and press it.
To switch the tool off, release
the on/off switch.
Hints for optimum use
Always use the correct type
and size of screwdriver bit.
If screws are difficult to
tighten, try applying a small
amount of washing liquid or
soap as a lubricant.
Use the spindle lock to loosen
very tight screws or to firmly
tighten screws.
Always hold the tool and
screwdriver bit in a straight
line with the screw.
When screwing in wood, it is
recommended to drill a pilot
hole with a depth equal to
the length of the screw.
KC9036EUR.PM65 25-06-2001, 14:5310
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker kc 9036 ka at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker kc 9036 ka in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Finnish as an attachment in your email.

The manual is 0,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info