382774
7
Zoom out
Zoom in
Previous page
1/12
Next page
7
ENGLISH
Unlock and remove
screw (19). Loosen
anticlockwise using the
allen key (22), remove
the outer washer (20)
and remove the blade.
Insert the new blade,
ensuring that the arrow
on the blade points in the same direction as the arrow
on the body of your circular saw. Fit the outer washer
(20). Ensure that this washer is correctly located on the
flats of the spindle. Fit the saw blade locking screw
(19). Insert a screwdriver through the hole in the blade
to prevent rotation of the blade. Tighten the sawblade
locking screw clockwise using the allen key (22).
ADJUSTING THE RIVING KNIFE
The riving knife (4) prevents the saw blade from
jamming during rip sawing operations. You must check
the position of the riving knife whenever the saw blade
is replaced, or whenever the clearance is affected.
Proceed as follows:
Disconnect the battery at the rear of the unit.
Through the opening in
the upper blade guard,
locate the riving knife
screw. Use allen key (22)
to loosen the riving knife
screw. Adjust the riving
knife to give a radial
clearance of 2-3mm and
a tooth peak clearance
of 2-3mm. Tighten the
riving knife screw.
Your saw is now ready for use.
OPERATING YOUR CIRCULAR SAW
To switch your circular
saw on, depress the
lock-off button (7) and
squeeze the on/off
trigger switch (2).
To stop your circular
saw, release the trigger switch.
HOLDING YOUR CIRCULAR SAW
The front handle (8)
makes it easier to guide
the saw properly. Switch
the machine on before
you start sawing the
workpiece. Guide the
saw without pushing it
and give the blade time to pursue its path. Use the
mark (14) for straight cuts or the mark (15) for mitring
cuts, to keep to the line you have drawn.
MAINTENANCE OF THE WINDOW
From time to time, it may become necessary to remove
cutting debris/dust from the inside of your circular saw
window.
To do this, proceed as follows:
Disconnect the battery
pack (1) from the Saw.
Remove the allen key
(22) from the sight
guide (13), and insert
into the left of (9).
Push the spring to the
right, and lift the window
up until it will not go any further, do not force it open. It
can now be cleaned with a lint free cloth. Let the
window close and replace the allen key (22) to sight
guide (13).
Note: If necessary, use only mild soap to clean your saw
as many household cleaners contain chemicals which
could seriously damage the plastic. Also, do not use
petrol, turpentine, laquer or paint thinners or simular
products. Never let any liquid get inside your circular
saw and never immerse any part of it into liquid.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker kc 1440 sk at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker kc 1440 sk in the language / languages: English as an attachment in your email.

The manual is 0,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info