390168
9
Zoom out
Zoom in
Previous page
1/92
Next page
9
ENGLISH
If the plug has a fuse cover, make sure that the
fuse cover is fitted. Do not use the plug if the
fuse cover is missing or damaged.
Never use a light socket.
Using an extension cable
Always use an approved extension cable suitable
for the power input of this tool (see technical
data). Before use, inspect the extension cable for
signs of damage, wear and ageing. Replace the
extension cable if damaged or defective. When
using a cable reel, always unwind the cable
completely. Use of an extension cable not suitable
for the power input of the tool or which is
damaged or defective may result in a risk of fire
and electric shock.
CARTON CONTENTS
The carton contains:
1 Powerfile
1 Set of sanding belts
1 Straight arm
1 Narrow arm (KA293G)
1 Cranked arm (KA293G)
1 Instruction manual
Carefully unpack all parts.
Please note that additional items may be
found in the carton, depending on the letter
suffix following the catalogue number of your
tool.
OVERVIEW (fig. A)
1. On/off switch
2. Lock-on button
3. Secondary handle
4. Straight arm
5. Belt tensioning lever
6. Belt tracking knob
7. Variable speed control knob
8. Dustbag
9. Narrow arm (KA293G)
10. Cranked arm (KA293G)
ASSEMBLY
Before assembly, make sure that the tool
is switched off and unplugged.
Fitting and removing sanding arms (fig. B)
Before first use, you must fit the sanding arm to
the tool. A straight arm (sanding width 13 mm) is
supplied with all models. In addition, the KA293G
is supplied with the following:
- a narrow arm (sanding width 6 mm) for intricate
work
- a cranked arm for grooving and sanding in the
centre of workpieces and for reaching confined
areas
These parts are also available as an accessory from
your Black & Decker dealer.
Fitting
Make sure that the belt tensioning lever (5) is
in the position shown (B).
Loosen and remove the belt tracking knob (6).
Remove the tape retaining the spring (11) (if
present).
Check that the spring is located in its mounting
hole.
Position the arm (4) as shown.
Fit the belt tracking knob (6) and tighten it until
the arm is aligned with the tool.
Removing
Remove the sanding belt (if present) as
described below.
Loosen and remove the belt tracking knob (6).
Remove the arm.
Be careful not to lose the spring (11).
Fitting and removing sanding belts (fig. C)
Fitting
Move the belt tensioning lever (5) to the front
position (A).
Make sure that the arrows on the inside of the
sanding belt face the same direction as the
arrows (15) on the housing.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker ka 293 e at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker ka 293 e in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 1,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info