390168
10
Zoom out
Zoom in
Previous page
1/92
Next page
10
ENGLISH
Place the sanding belt (12) over the front
pulley (13) and the rear pulley (14), sliding it
through the slot in the housing.
Move the belt tensioning lever (5) to the rear
position (B).
Adjust the belt tracking as described below.
Removing
Move the belt tensioning lever (5) to the front
position (A).
Slide the sanding belt (12) off the pulleys.
Adjusting the sanding belt tracking (fig. D)
Switch the tool on.
Turn the belt tracking knob (6) as required until
the sanding belt runs straight along the length
of the arm.
Fitting and removing the dustbag (fig. E)
Make sure to remove the dustbag before
using the tool on metal workpieces.
Fitting
Align the dustbag (8) with the tool as shown.
Slide the dustbag onto the tool until it clicks
into place.
Removing
Pull the dustbag (8) to the rear and off the tool.
USE
Let the tool work at its own pace.
Do not overload.
Variable speed control (fig. F)
The variable speed control allows you to adapt the
speed of the tool to the workpiece material. Use a
low speed setting when using a fine grit, when
working with plastics or ceramics and when
removing painted or varnished surfaces. Use a
high speed setting when using a coarse grit and
when removing a lot of material.
Set the control knob (7) to the desired setting.
Switching on and off (fig. G)
To switch the tool on, press the on/off switch (1).
To switch the tool off, release the on/off switch.
For continuous operation:
- Press the on/off switch (1).
- Press the lock-on button (2).
- Release the on/off switch.
To switch the tool off when in continuous
operation, press and release on/off switch (1).
Emptying the dustbag (fig. E)
The dustbag should be emptied every 10 minutes
of use.
Pull the dustbag (8) to the rear and off the tool.
Hold the spout down and shake the dustbag
to empty the contents.
Refit the dustbag onto the tool.
If necessary, the dustbag can be removed from its
frame and washed. Let it dry before refitting it.
Special applications
Cranked arm (fig. H)
Use section A for grooving or sanding in the
centre of workpieces and in confined areas.
Use section B for curved surfaces.
Straight arm (fig. I)
Use the normal or narrow arm for general use,
for slotting and for making joints.
Narrow arm (fig. J)
Use the narrow arm for finer detail, for cutting
and for carving.
Hints for optimum use
Always hold the tool with both hands.
Do not exert too much pressure on the tool.
Regularly check the condition of the sanding
belt. Replace when necessary.
Always sand with the grain of the wood.
When sanding new layers of paint before
applying another layer, use extra fine grit.
On very uneven surfaces, or when removing
layers of paint, start with a coarse grit.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker ka 293 e at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker ka 293 e in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 1,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info