Manual Black Decker HVLP200 T1 (page 11 of 16) (English)

578632

Zoom out

Zoom in

1/16

ENGLISH

(Original instructions)

u Maintain smooth and consistent speed which will help

avoid inconsistencies. Begin spraying after the pass has

begun and release trigger before stopping the pass.

u Avoid spraying too heavily in any one area. Several lighter

coats are better than one heavy coat which can lead to

running and dripping. Remember that the ow control

knob regulates the amount of liquid that can be sprayed.

Turning the ow knob clockwise increases the ow of

liquid. Turning the knob counterclockwise decreases the

ow of liquid. If runs or drips do occur, have a dry paint

brush on hand to smooth them out.

u Turn the power unit off and place the sprayer in the built-in

dock of the power unit when not spraying for any length of

time.

Maintenance and cleaning

Your Black & Decker corded appliance has been designed to

operate over a long period of time with a minimum of main-

tenance. Continuous satisfactory operation depends upon

proper appliance care and regular cleaning.

Warning! Be sure to use appropriate personal protective

equipment.

Warning! Before performing any maintenance or cleaning on

corded appliances switch off and unplug the appliance.

Warning! Do not use materials with a ashpoint lower than

55°C. Flashpoint is the temperature that a uid can produce

enough vapours to ignite (see paint supplier instructions).

Warning! Make sure clean up area is well ventilated and free

of ammable vapours.

Warning! Always spray outdoors when spraying cleaning

solution through sprayer.

Warning! Do not submerse power unit.

Flushing the sprayer (g. N)

u Disconnect the sprayer from the power supply.

u Unscrew the lid from the side of the canister and pour any

remaining liquid back into the original container (g. N).

u Pour a small amount of the appropriate cleaning solution

into the canister.

t Warm soapy water for water based materials.

t Manufacturers recommended cleaning solution for oil

based materials.

u Replace the lid on the canister securely and vigorously

shake the sprayer.

u Unscrew the lid from the side of the canister and properly

dispose of cleaning solution.

u Rell the canister with a small amount of new cleaning

solution. Screw lid securely on canister.

u Reattach the sprayer to the motor unit, plug in the cord

and turn on the power unit.

u Spray the cleaning solution through the sprayer onto scrap

material for 2 to 3 seconds.

Cleaning the sprayer (g. O - S)

u Disconnect the sprayer from the power supply.

u Remove the side ll canister (6) and unscrew the side

lid (7). Remove the check valve (18), pickup tube (15)

and o-ring (17) from the sprayer. Clean the parts in the

appropriate cleaning solution (g. O).

u Unscrew the tip collar (19) and remove the spray nozzle

(10) and spray tip (20). Clean all parts in the appropriate

cleaning solution (g. P).

u If using water based material, clean the sprayer by running

water through pickup tube inlet. If using oil based materi-

als, clean pickup tube inlet with the appropriate cleaning

solution. Repeat until sprayer is completely clean. Take

special care to gently clean the spraying needle (21).

u Dry all parts thoroughly.

u Properly dispose of cleaning solution.

u Place a drop of household oil onto the metal ball in the

check valve (18) (g. Q).

Important : Lubricating the ball in check valve (18), after

cleanup, will help to prevent it from sticking which can clog the

valve and prevent adequate ow of spray material.

Note : When reassembling, place metal ball end of check

valve (18) into sprayer.

u Reassemble sprayer (g. S).

Note : The spray tip (20) can only go in one way. The notch

(22) on the spray tip must align with the recess in the threads

of the sprayer (g. R).

Cleaning the power unit

u Disconnect the sprayer from the power supply.

u Use only mild soap and damp cloth to clean the power

unit.

Warning! Never let any liquid get inside the power unit.

Warning! Never immerse any part of the power unit into a

liquid.

Cleaning the lter

The power unit contains a washable/reusable lter (g. T).

Check the lter before and after each use. If dirty, wash with

warm water and allow to air dry before re-installing or replace

if necessary.

u To check the lter, remove the lter cover (11) by removing

the 2 screws from the top of the lter cover then pulling

the cover off the power unit.

u Remove the lter (23) and inspect.

u Replace the lter and lter cover.

Warning! Never operate the power unit without the lter in

place. Debris could be sucked in and interfere with the func-

tion of the power unit.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker HVLP200 T1 in the language / languages: English as an attachment in your email.

The manual is 2,87 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker HVLP200 T1

Black Decker HVLP200 T1 User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 112 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker HVLP200 T1 Manual

Product: