Manual Black Decker HVLP200 T1 (page 10 of 16) (English)

578632

Zoom out

Zoom in

1/16

ENGLISH

(Original instructions)

Note : Always test the spray pattern on scrap cardboard

or similar material rst. Begin with ow control knob on the

highest ow setting. If less ow is desired, dial the ow control

knob in. Heavier, thicker materials should be sprayed with the

indicator close to the (+) icon. Thinner materials should be

sprayed with the indicator close to the (-) icon.

Note : If the ow control setting is set completely to the

minimum side, the trigger will have limited or no travel. Back

the ow control knob off (clockwise) to allow for more trigger

travel.

Liquid material preparation (g. J & K)

Note : Make sure the type of material you use can be cleaned

with either mineral spirits or paint thinner (for oil-based paints)

or a warm water and soap solution (for water soluble paints

like latex). Use drop cloths to protect your oors and anything

else in the spraying area that you wish to remain untouched.

The liquid being sprayed may need to be thinned (diluted)

before staring. When thinning, use the proper liquid thinner

recommended on the container by the material manufacturer.

Warning! Do not use materials with a ashpoint lower than

55°C.

Note : A mixing bucket (12) is provided to use when transfer-

ring spray material from the original container into the bucket

for thinning and measuring purposes (g. J).

Note : A viscosity cup (13) is provided to determine the

“runout time” of the material being used.

u Before measuring for the proper viscosity, stir the material

thoroughly.

u Dip the viscosity cup (13) into the material being sprayed

and ll the viscosity cup (13) completely.

u With the viscosity cup (13) held over the material con-

tainer, measure the amount of time it takes for the stream

of material owing out to “break” or stop being a constant

stream out of the bottom of the viscosity cup (13) (2

minutes or less) (g. K). This is the “runout time” Refer to

the thinning table for information on the thinning required

for different materials.

u If material needs thinning, add the appropriate liquid thin-

ning material recommended by the manufacturer.

u It is possible to spray latex paint with this unit, however,

the required thinning may exceed material manufacturer's

recommendation. Thin latex paint so that it runs through

viscosity cup (13) in under 2 minutes. The operator should

consider the type of application and nal location of the

project when spraying a material that requires more than 2

minutes to run through the viscosity cup (13).

Thinning table

Spray material Runout time

Clear and semi-transparent stains

and sealers

No thinning required

Oil based primers, varnishes and

polyurethane

(Less than 2 minute runout)

Solid colour water based stains May require thinning

Water based or latex paints (More than 2 minute runout)

Note : Not recommended for textured paint

Hints for optimum use

Preparation tips

u Always stir and strain the material thoroughly before use.

u With any spraying job you should always ensure that

you have properly prepared the surface to get the best

nish. That is, all surfaces are free from dust, dirt, rust and

grease. Lightly pressure wash decks or exterior surfaces

and ensure that they are dry before spraying.

u Even though HVLP sprayers have very little overspray,

it is recommended that you mask all edges and other

areas and use drop cloths to protect your oors and

anything else in the spraying area that you wish to remain

untouched.

u Skin that forms on the top of paint can clog the sprayer.

Remove skin before mixing. Strain with a funnel with a

lter attached or through hosiery to remove any impurities

that could clog system.

u Before starting have gloves, paper towels, rags etc. avail-

able for unexpected spills.

Developing the proper spraying technique (g. L & M)

u Practice spraying on a piece of scrap material such as

cardboard to test your spray pattern and become familiar

with the ow control feature of the sprayer.

u Ensure surface to be sprayed is free of dust, dirt, and

grease.

u Ensure spray area is clean and free of dust that could be

blown onto newly sprayed surfaces.

u Cover any areas not intended to be sprayed.

u Always spray from a minimum of 25mm to a maximum of

355mm (g. L).

u A commonly used method for spraying a large surface

is the “crisscross” pattern. This is done by spraying in

horizontal strips and then crossing over these strips with

vertical strips.

u To get an even spray distribution, always keep your arm at

the same distance (g. L) from the surface you are spray-

ing and avoid moving your wrist (g. M).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker HVLP200 T1 in the language / languages: English as an attachment in your email.

The manual is 2,87 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker HVLP200 T1

Black Decker HVLP200 T1 User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 112 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker HVLP200 T1 Manual

Product: