Manual Black Decker HPL108 TH1 (page 9 of 112) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

581139

Zoom out

Zoom in

1/112

ENGLISH

(Original instructions)

Charger diagnostics

If the charger detects a weak or damaged battery, the charg-

ing indicator (11) will ash red at a fast rate. Proceed as

follows:

u Re-insert the battery (4).

u If the charging indicators continues ashing red at a fast

rate, use a different battery to determine if the charging

process works properly.

u If the replaced battery charges correctly, the original

battery is defective and should be returned to a service

centre for recycling.

u If the new battery gives the same indication as the original

battery, take the charger to be tested at an authorised

services centre.

Note: It may take as long as 60 minutes to determine that

the battery is defective. If the battery is too hot or too

cold, the LED will alternately blink red, fast and slow, one

ash at each speed and repeat.

Variable speed control (g. I)

The variable speed control allows you to adapt the speed of

the tool to the application.

u Set the variable speed dial (2) to the desired setting. At

setting 1 the tool will operate at low speed, 7,500 min-1.

At setting 6 the tool will operate at the maximum speed,

15,000 min-1.

Switching on and off (g. J)

u To switch the tool on, slide the on/off switch (1) forward

(position I).

u To switch the tool off, slide the on/off switch (1) to the rear

(position O).

LED work light

The LED work light (6) is activated automatically when the tool

is switched on.

Low-battery Indicator

If the LED worklight (6) begins to rapidly and continuously

ash when the switch on the tool is depressed, the battery-

pack power has run out, and the battery pack should be

recharged.

Unlike other battery pack types, Lithium-Ion battery packs

deliver fade-free power for their entire run time. The tool will

not experience a slow, gradual loss of power as you work. To

signal that the battery pack is at the end of its run time and

needs to be charged, the power to the tool will drop quickly.

Note: The LED may also ash due to an overload or high

temperature (see Battery Protection)..

Battery Protection

The battery circuitry protects the battery pack from extreme

temperature, over discharge, and over-charge. To protect the

battery from damage and prolong its life, the battery pack

circuitry will turn off the battery pack if it becomes overloaded

or if the temperature becomes too high during use. This may

happen in situations involving extremely high torque, binding

and stalling. This intelligent system will shut down your battery

pack if its operating temperature exceeds 80°C and will begin

normal operation when it returns to 0°C – 50°C.

The LED worklight light will begin to ash slowly if the battery

circuitry detects a momentary overload.

Note: The battery can automatically reset. If the LED

continues to ash rapidly, it is indicating that the charge

is substantially diminished. Place the battery into the

charger for charging.

Note: A signicantly reduced run time after fully charging

the battery pack indicates that the battery is near the end

of its usable life and must be replaced.

Hints for optimum use

u Always hold the tool securely. For precision work, hold the

tool near the front.

u Clamp the workpiece whenever possible, especially when

using cutting blades.

u Do not exert too much pressure on the tool.

u Always use the appropriate type of attachment for the

workpiece material and type of cut.

u Regularly check the condition of accessories. Replace

when necessary.

u Mark the desired starting point.

u Switch the tool on and slowly feed attachments into the

workpiece at the desired starting point.

u Clamp a piece of plywood or soft wood to the back of the

workpiece and saw through the combination in order to

obtain a clear cut.

u Do not force the cutting blade into the workpiece. Note

that cutting sheet metal will normally take more time than

sawing thicker wooden workpieces.

u When cutting metal spread a thin lm of oil along the cut-

ting line before cutting.

u When sanding new layers of paint before applying another

layer, use extra ne grit.

u On very uneven surfaces, or when removing layers of

paint, start with a coarse grit. On other surfaces, start with

a medium grit. In both cases, gradually change to a ne

grit for a smooth nish.

u Consult your retailer for more information on available

accessories.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker HPL108 TH1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 9,53 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker HPL108 TH1

Black Decker HPL108 TH1 User Manual - Turkish - 12 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker HPL108 TH1 Manual

Product: