Manual Black Decker HPL108 TH1 (page 8 of 112) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

581139

Zoom out

Zoom in

1/112

ENGLISH

(Original instructions)

Fitting and removing the accessories (g. C - H)

Warning! Before tting an accessory, disconnect the tool from

the mains supply.

Fitting a Black & Decker / Piranha accessory (g. C - E)

u Hold the tool and squeeze the accessory clamping lever

(3).

u Slide the accessory (13) between the shaft and the acces-

sory holder making sure the accessory engages all eight

pins on the holder and is ush with the shaft.

u Release the accessory clamping lever.

Note: Some accessories, such as scrapers and blades can be

mounted at an angle if required (g. E).

Removing a Black & Decker / Piranha accessory (g. C)

u Hold the tool and squeeze the accessory clamping lever

(3).

u Pull the accessory from the tool making sure the acces-

sory dis-engages from all eight pins on the holder.

u Release the accessory clamping lever.

Warning: Gloves must be worn when removing accessories

as they may become hot during use.

Fitting a sanding sheet (g. F)

u Line up the sanding sheet (14) with the sanding base (6)

as shown.

u Press the sheet rmly and evenly onto the sanding base,

making sure that the holes in the sheet coincide with the

holes in the base.

Removing a sanding sheet

u Pull the sanding sheet (14) off the sanding base (6).

Warning! Never use the sanding base without a sanding

sheet or accessory in place.

Fitting the dust extraction adaptor (g. G) (Where

supplied - Accessory part number : 'Item 58 from the

service sheet found at the end of this instruction manual')

u Line up the dust extraction adaptor (7) with the sanding

base (6) as shown.

u Press the adaptor rmly and evenly in to the sanding

base.

u Secure the adaptor by turning the locking nut (17) clock-

wise.

u Connect a vacuum cleaner to the dust extraction adaptor.

Removing the dust extraction adaptor

u Turn the locking nut (17) anti-clockwise.

u Pull the dust extraction adaptor (7) out of the sanding

base (6).

Fitting alternative accessories (g. H)

u Place the spacer (8) onto the collar (15).

u Place the alternative accessory (16) onto the collar (15).

u Firmly attach the xing bolt (9) into place to ensure a tight

t for the alternative accessory (16).

Note: The spacer and xing bolt are not used to attach Black

& Decker accessories. Black and Decker accessories are

attached using the Super-lok

Tool free accessory clamping

lever.

Use

Warning! Let the tool work at its own pace. Do not overload.

Warning! Before cutting into walls, oors or ceilings, check for

the location of wiring and pipes.

Charging the battery (g. A)

The battery needs to be charged before rst use and whenev-

er it fails to produce sufcient power on jobs that were easily

done before. The battery may become warm while charging;

this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 10 °C or above 40 °C. Recommended charging tem-

perature: approx. 24 °C.

Note: The charger will not charge a battery if the cell

temperature is below approximately 0 °C or above 40 °C.

The battery should be left in the charger and the charger

will begin to charge automatically when the cell tempera-

ture warms up or cools down.

u To charge the battery (4), insert it into the charger (10).

The battery will only t into the charger in one way. Do

not force. Be sure that the battery is fully seated in the

charger.

u Plug in the charger and switch on at the mains.

The charging indicator (11) will ash green continuously

(slowly).

The charge is complete when the charging indicator (11)

lights green continuously. The charger and the battery can be

left connected indenitely with the LED illuminated. The LED

will change to ashing green (charging) state as the charger

occasionally tops off the battery charge. The charging indica-

tor (11) will be lit as long as the battery is connected to the

plugged-in charger.

u Charge discharged batteries within 1 week. Battery life will

be greatly diminished if stored in a discharged state.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

LED glowing indenitely. The charger will keep the battery

pack fresh and fully charged.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker HPL108 TH1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 9,53 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker HPL108 TH1

Black Decker HPL108 TH1 User Manual - Turkish - 12 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker HPL108 TH1 Manual

Product: