Manual Black Decker HP188 (page 11 of 104) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

472990

Zoom out

Zoom in

1/104

ENGLISH

◆ To remove the chuck (4), keep the release tabs

(18) depressed and pull the chuck off the

spindle (19).

◆ Install a screwdriver bit (20) by pushing it into

the spindle (19) as shown. To remove the

screwdriver bit, pull the ring (21) back and pull

the screwdriver bit out of the spindle.

◆ To refit the chuck, push it onto the spindle

until it is firmly locked into place.

Always make sure that the chuck is

securely fitted.

HP188F2 - Fitting the side handle (fig. A)

◆ Loosen the side handle (8) by turning it

counterclockwise.

◆ Slide the side handle over the chuck and onto

the housing.

◆ Tighten the side handle by turning it clockwise.

USE

Let the tool work at its own pace.

Do not overload.

Charging the battery (fig. E)

The battery needs to be charged before first use

and whenever it fails to produce sufficient power

on jobs that were easily done before.

A new battery, or a battery that has not been used

for an extended period of time, achieves full

performance only after approx. 5 charging and

discharging cycles. The battery may become warm

while charging; this is normal and does not

indicate a problem.

Do not charge the battery at ambient

temperatures below 4 °C or above 40 °C.

Recommended charging temperature:

approx. 24 °C.

After normal use, a charging time of 60 minutes

will provide sufficient power for most applications.

However, further charging for up to 90 minutes

could significantly increase the use time,

depending on the battery and charging

conditions.

◆ To charge the battery (9), remove it from the

tool and insert it into the charger (11).

The battery will only fit into the charger in one

way. Do not force. Be sure that the battery is

fully seated in the charger.

◆ Plug in the charger.

◆ Check if the red charging indicator (12) lights

up. If the green end of charge indicator (13)

lights up now instead, the battery is too hot

and cannot be charged. If this happens,

remove the battery from the charger, let the

battery cool down for approx. 1 hour and

re-insert it.

After approx. 1 hour of charging, the red charging

indicator (12) will stop lighting and the green end

of charge indicator (13) will light up. The battery is

now fully charged.

◆ Remove the battery from the charger.

HP128F2/HP148F2/HP188F2 - Checking the

battery condition (fig. F)

This tool is fitted with a battery charge indicator,

which allows you to check the condition of the

battery.

◆ Press and hold down the button (22).

◆ Check to see how many of the lights (23) are on:

Battery charge

1 light low

2 lights medium

3 lights high

Selecting the direction of rotation (fig. G)

For drilling and for tightening screws, use forward

(clockwise) rotation. For loosening screws or

removing a jammed drill bit, use reverse

(counterclockwise) rotation.

◆ To select forward rotation, push the forward/

reverse slider (2) to the left.

◆ To select reverse rotation, push the forward/

reverse slider to the right.

◆ To lock the tool, set the forward/reverse slider

into the centre position.

Selecting the operating mode or torque (fig.H)

This tool is fitted with a collar to select the operating

mode and to set the torque for tightening screws.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker HP188 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,66 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker HP188 Manual

Product: