Manual Black Decker HP188 (page 10 of 104) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

472990

Zoom out

Zoom in

1/104

ENGLISH

Mains plug replacement (U.K. & Ireland only)

◆ Should your mains plug need replacing and

you are competent to do this, proceed as

instructed below. If you are in doubt,

contact an authorised repair agent or a

qualified electrician.

◆ Disconnect the plug from the supply and

remove the fuse from the plug.

◆ Cut off the plug and dispose of it safely; a plug

with bared copper conductors is dangerous if

engaged in a live socket outlet.

◆ Only fit 13 Amperes BS1363A approved plugs

fitted with a 5 A fuse (1).

◆ The cable wire colours, or a letter, will be

marked at the connection points of most good

quality plugs. Attach the wires to their

respective points in the plug (see above).

Brown is for Live (L) (2), blue is for Neutral (N) (4).

◆ Before replacing the top cover of the mains

plug ensure that the cable restraint (3) is

holding the outer sheath of the cable firmly

and that the leads are correctly fixed at the

terminal screws.

◆ If the plug has a fuse cover, make sure that the

fuse cover is fitted. Do not use the plug if the

fuse cover is missing or damaged.

Never use a light socket.

OVERVIEW (fig. A)

1. Variable speed switch

2. Forward/reverse slider

3. Mode selector / torque adjustment collar

4. Chuck

5. Two-gear selector

6. Battery charge indicator

(HP128F2/HP148F2/HP188F2)

7. Bit holder

8. Side handle (HP188F2)

9. Battery

10. Battery release button

11. Charger

12. Charging indicator

13. End of charge indicator

ASSEMBLY

Fitting and removing the battery (fig. B)

◆ To fit the battery (9), line it up with the

receptacle on the tool. Slide the battery into

the receptacle and push until the battery snaps

into place.

◆ To remove the battery, push the release

button (10) while at the same time pulling the

battery out of the receptacle.

Fitting and removing a drill bit or screwdriver

bit (fig. A & C)

This tool is fitted with a keyless chuck to allow for

an easy exchange of bits.

◆ Lock the tool by setting the forward/reverse

slider (2) to the centre position (fig. A).

◆ Open the chuck by turning the front part (15)

with one hand while holding the rear part (16)

with the other (fig. C).

◆ Insert the bit shaft (17) into the chuck.

◆ Firmly tighten the chuck by turning the front

part (15) with one hand while holding the rear

part (16) with the other.

This tool is supplied with a double-ended

screwdriver bit in the bit holder (7) (fig. A).

◆ To remove the screwdriver bit from the bit

holder, lift the bit from the recess.

◆ To store the screwdriver bit, firmly push it into

the holder.

HP126F2/HP146F2 - Removing and fitting the

chuck (fig. D)

The chuck on these models can be easily removed

and refitted. When your project entails both

drilling and screwdriving, fit a screwriver bit in the

spindle and a drill bit in the chuck: you will then

only need to remove the chuck for screwdriving

and refit it for drilling. The screwdriver bit can be

left in the spindle while drilling. You can also fit

drill bits with a hexagonal shaft in this way.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker HP188 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,66 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker HP188 Manual

Product: