586100

Black Decker GX302 T6 Manual

7
Zoom out
Zoom in
Previous page
1/47
Next page
7
ENGLISH
Overload protection
Your mower is fitted with overload protection.
The reset button (33) can be found on the switch box
(Fig. A).
If you work too quickly in long grass, or in heavy
cutting conditions, you may overload the motor.
This will be indicated by a significant drop in speed,
and eventually the overload protection will operate.
This is not a fault but a safety device to protect
your mower.
When this occurs, release the switch and wait for
2 to 3 minutes to allow the motor to cool, then press
the reset button (33) and restart by operating the
switch lever.
If the cut-out operates again within 10 minutes you
should increase the height of cut (see “Height of cut
adjustment”) and walk more slowly.
Severe overloading may result in a longer delay on
restarting. In such cases, after resetting, you should
allow the motor to cool.
Blade maintenance
Steel blades
The steel blade is designed to give a fine
finish in long or tough grass. The blade will
continue to cut even when it has become
blunt or burred. There is no need for it to be
razor sharp.
If, however, because of damage or wear the
cutting performance deteriorates, then your
mower may require a new blade, or at least
the existing blade to be sharpened.
We recommend that the steel blade is
sharpened or a new blade fitted at the
beginning of each season.
Plastic blades
Plastic blades will wear during use. This type
of blade cannot be sharpened and should be
discarded and new blades fitted when worn.
Note: Plastic blades should be replaced in
pairs, not singly.
A number of spare blades are supplied with
the plastic blade cutting system when
purchased separately.
Replacement blades are available from
Black & Decker service agents.
!
Warning! When fitting a new blade use only
the Black & Decker replacement part
specified for your mower - do not attempt to
fit any other blade.
Fitting a new blade
!
Observe all the relevant warnings before
changing blades.
Details on the fitment of new steel blades are
given in “Cut height adjustment”. Details on
the fitment of new plastic blades are given in
“Changing to the plastic blade system”.
Handy hints
• Before starting your mower on grass always tilt it
to one side slightly and allow it to run up to
maximum speed before commencing to cut the
grass. This will maximise the hover effect and will
prevent the blades from digging into the grass.
• On long grass, above 10cm (4 inches), use two
cuts to get a close finish. We recommend that
the first cut should be taken with the blade set at
maximum height of cut and the second taken
with it set at medium or close. This will prove to
be easier and give a better overall finish to
your lawn.
Care and maintenance
The advice given in this section covers the
general care and maintenance of the main
body of your mower. Advice relating to the
blades is given in “Maintenance of blades”.
!
Warning! Do not use a cable which
shows signs of damage. Fit a new cable
completely - do not make any permanent or
temporary repairs.
• Always keep your mower clean and free
from grass cuttings, especially the
underside of the cutter cover and the air
vents.
• Check all electrical cables at regular
intervals, looking for signs of wear,
abrasion or other damage.
• At the end of each cutting session we
recommend that the build up of grass on
the underside of the cutter cover is
removed using a blunt scraper or the
spanner supplied.
• Remove grass cuttings from the slot
between the pivot block flanges.
• Clean all plastic components with a
damp cloth.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker GX302 T6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GX302 T6 in the language / languages: English, German, Dutch, French, Spanish, Spanish as an attachment in your email.

The manual is 0,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info