Manual Black Decker GX302 T6 (page 6 of 47) (English, German, Dutch, French, Spanish, Spanish)

586100

Zoom out

Zoom in

1/47

• Place the bulk of the extension cable

on the lawn close to the starting point

(Fig. Ja position 1).

Your switch box incorporates a cable

restraint. To fix the cable to the restraint,

proceed as follows:

• Bring the socket end of the extension

cable from behind and connect it to your

mower plug.

• Form a loop on your extension cable

close to the switchbox.

• Push the loop through the slot from

the opposite side of the restraint hook,

position the loop over the hook and

pull the cable back through the slot.

Your cable will now be restrained.

• The extension cable should now fall

away from your mower and behind the

operator, ready for use.

Warning! Do not attempt to operate your

mower with one hand - you must guide it

with both hands.

• Lift the handle up to release it from the

park position.

• Tilt the unit slightly on its side to reduce

the risk of lawn damage whilst starting,

depress the safety lock-off button (15)

on the switchbox (13) (Fig. D), and whilst

still depressed pull the switch lever (14)

towards you. Your mower will start, and

you can now allow it to return to its

proper cutting position, and commence

cutting.

• Proceed down the cutting area as

shown in Fig. Ja, working from position

1 towards position 2 and, on reaching

position 2, turn to the right and proceed

towards position 3. Continue to the end

of the cutting area, turn to the left, and

proceed towards position 4. Continue in

the same manner as shown in Fig. Ja,

always working away from the cable.

Do not adopt the method shown in

Fig. Jb, working towards the cable,

as this can be dangerous.

Your mower will continue to operate whilst

you are pressing the switch lever. If you

release it for any reason you will not be able

to press it again until you have pressed the

safety lock-off switch on the switch box.

This feature prevents accidental restart.

When you have finished using your mower

we recommend that you clean all debris

from it before putting it away. Refer to the

“Care and maintenance” section.

Note: To obtain the best results cut your

lawn or grassed area regularly and do not

cut when the grass is wet.

Changing to the plastic blade system

(Fig. K)

A plastic cutter blade system can be

purchased as an accessory for your mower.

This system comprises a blade carrier and a

number of blades.

The steel blade is designed to give a fine

finish in long or tough grass.

The plastic blade system can be used for

safer cutting in normal conditions. It should

not be used to cut tough or long grass as

the plastic blades are not designed for

this purpose.

To remove the steel blade and to fit the

plastic blade system, proceed as follows:

Warning! Disconnect your mower from the

electrical supply before fitting the plastic

blade system.

• Remove the steel blade as described in

“Height of cut adjustment” but retain the

two thicker spacers and the nut.

• If you wish to alter the height of cut

whilst fitting the plastic blade system

then follow the instructions given in

“Height of cut adjustment”.

• Using a damp cloth, clean the contact

faces of the spacer rings, removing any

grass or debris.

• Fit any spacers necessary to give the

correct height adjustment, fit the blade

carrier (25) on to the motor spindle with

the ribbed face towards the impeller,

fit any remaining spacers and fit the nut.

Use a cloth or wear a heavy duty glove

to prevent the blade carrier from turning

and tighten the nut with the spanner

provided.

Note: Instructions on how to fit the blade

carrier to your mower are also given on a

label on the blade carrier.

• Attach two plastic blades (30) to the

blade carrier (25), by placing one blade

on each blade pivot (31) and pull the

blades outwards so that they are locked

into position.

• Your mower is now ready for use.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GX302 T6 in the language / languages: English, German, Dutch, French, Spanish, Spanish as an attachment in your email.

The manual is 0,4 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker GX302 T6 Manual

Product: