Manual Black Decker GR350 (page 6 of 60) (English, German, Dutch, French, Italian, Portuguese, Spanish)

474467

Zoom out

Zoom in

1/60

Blade maintenance

The steel blade is designed to give a fine

finish in long or tough grass. The blade will

continue to cut even when it has become

blunt or burred. There is no need for it to be

razor sharp.

If, however, because of damage or wear the

cutting performance deteriorates, then your

mower may require a new blade, or at least

the existing blade to be sharpened.

We recommend that the steel blade is

sharpened or a new blade fitted at the

beginning of each season.

Replacement blades are available from

Black & Decker service agents.

Warning! When fitting a new blade use only

the Black & Decker replacement part

specified for your mower - do not attempt to

fit any other blade.

Fitting a new blade (Fig. F)

Observe all the relevant warnings before

changing the blade.

Warning! Disconnect your mower from the

electrical supply before changing the blade.

• Turn your mower over on its side so that

the underside of the cutter deck is

exposed.

• Using a cloth placed over the blade or

heavy duty gloves to protect your hands,

grip the blade and, using the spanner

provided, loosen and remove the nut (30)

from the motor spindle. Turn the nut in an

anti-clockwise direction to loosen it.

• The blade can now be replaced and the

washer and nut re-assembled.

Note: With the introduction of a new style

GR360C the replacement blade will only fit

the correct series model. The series model is

printed on the rating plate situated on the

underside of the switch box. The information

will be found on the small sticker containing

all the technical data. The correct

replacement blades are as follows:

GR360C Series 6 - A6116

GR360C Series 7 - A6117

Please note, the replacement blades will only

fit the correct mower.

Note: Some mowers are fitted with a clutch

washer between the blade nut and the blade,

which must be re-assembled at all times.

Handy hints

• On long grass, above 10cm (4 inches), use two

cuts to get a close finish. We recommend that

the first cut should be taken with the blade set at

maximum height of cut and the second taken

with it set at medium or close. This will prove to

be easier and give a better overall finish to

your lawn.

Care and maintenance

The advice given in this section covers the

general care and maintenance of the main

body of your mower. Advice relating to the

blades is given in “Maintenance of blades”.

Warning! Do not use an extension cable

which shows signs of damage. Fit a new

cable completely - do not make any

permanent or temporary repairs.

• Always keep your mower clean and free

from grass cuttings, especially the

underside of the cutter deck and the

air vents.

• Check all electrical cables at regular

intervals, looking for signs of wear,

abrasion or other damage.

• At the end of each cutting session we

recommend that the build up of grass on

the underside of the cutter cover is

removed using a blunt scraper.

• Clean all plastic components with a

damp cloth.

Caution: Do not use solvents or cleaning

fluids as these may damage the plastic

components of your mower.

Fault finding

If your mower does not operate correctly,

use the following table to locate the problem.

Warning! Always disconnect your mower

from the electrical supply before carrying out

any inspection.

Symptoms Possible cause Remedy

Motor buzzes Blade jammed. Disconnect from

but blade does the electrical supply.

not move. Remove

obstruction from

the blade.

No noise and Faulty electrical Disconnect from

blade does connection. the electrical

not move. supply.

Plug your mower

into an alternative

compatible

electrical supply.

Fit a new fuse.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GR350 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,87 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker GR350 Manual

Product: