474467

Black Decker GR350 Manual

4
Zoom out
Zoom in
Previous page
1/60
Next page
4
The handle (9) comprises the lower handle
(10), upper handle (11), switch box (24),
switch lever (21) and safety lock-off button
(20), electrical supply cable (19), cable clips
(12,13) and the handle clamp assemblies,
which comprise a wing nut (15), washer (16)
and bolt (17).
Assemble the lower handle (10) into correct
locations on your mower body, as follows:
B
• The lower handle (10) comes ready
assembled to your mower body (1) by
means of a pivot pin (8), wing nuts (15),
and washers (16). All that is required is to
unfold the handle from your mower body
by lifting, until the handle ends snap into
the correct locations on the sides of your
mower body. Once this is complete the
wing nuts (15) can be tightened.
With the lower handle in position, assemble
the upper handle, as follows:
C
• Place the upper handle (11) over the
lower handle (10), with the upper bend
as shown in Fig. A.
• Align the lower holes in the upper handle
with the location pins (18) in the lower
handle and press the upper handle onto
these pins.
• Align the remaining (upper) holes in both
the upper and lower handles and fit a
bolt (17) through each hole. Fit a washer
(16) to each bolt and fit the wing nuts
(15) on to the bolts. Tighten each one
with hand pressure only.
Note: Do not use a spanner or other
implement to tighten the wing nuts.
When both upper and lower handle tubes
are assembled, fix the cable (19) by means
of the cable clips (12 &13) to the completed
handle, as follows:
D
• The lower cable clip (12) fits into the hole
in the lower handle tube (10) and has a
location pin for that purpose.
• The upper cable clip (13) fits onto the
upper handle tube (11) and can be
fitted in any position along the upper
side stem.
• Having completed the above, secure
the cable to the handle by pushing into
the clip lugs.
Height of cut adjustment (Fig. G)
!
Warning! Disconnect your mower from
the electrical supply before making any
adjustment and give the blade time to stop
rotating: cutting blades are sharp.
• Only fit BS1363A approved plugs fitted
with the correctly rated fuse.
• The cable wire colours, or a letter, will be
marked at the connection points of most
good quality plugs. Attach the wires to
their respective points in the plug (see
below). Brown is for “Live” (L) and blue is
for “Neutral” (N).
• Before replacing the top cover of the
mains plug ensure that the cable restraint
is holding the outer sheath on the cable
firmly and that the two leads are correctly
fixed at the terminal screws.
Fit a
BS1363A
approved
plug
Connect blue
to N (neutral)
Make sure that the
outer sheath of the
cable is held firmly
by the clamp
Fit the
recommended
fuse
Connect brown
to L (live)
240 volts AC only.
Never use a light
socket
!
Warning! Never connect live or neutral wires
to the earth pin marked “E” or .
Note: Do not wire an extension cable directly
into your mower yourself. Instead, take your
mower to your nearest Black & Decker
service agent.
Increased safety can be obtained by having
a qualified electrician install a high sensitivity
(30mA) circuit breaker in the house wiring.
If you do not have such a circuit breaker
installed, or you do not wish to have one
installed, then we strongly recommend that
the electrical power to your mower be
supplied through a high sensitivity residual
current device (RCD). The RCD is designed
to provide a high degree of personal
protection against harmful electric current
should fault conditions occur.
!
Warning! The use of an RCD or other circuit
breaker unit does not release the operator of
your mower from the safety instructions and
safe working practices given in this manual.
Handle assembly (Fig. A - D)
A
Remove the parts from the carton and
familiarise yourself with the individual parts of
your mower.
The main parts of your mower are mower
body (1) which comprises the cutter deck (2),
cutter cover (3), collar (4), motor cover (5),
wheels (6), grassflap (7) and pivot pin (8).
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker GR350 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GR350 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info