Manual Black Decker GR346 (page 5 of 16) (English)

529726

Zoom out

Zoom in

1/16

ENGLISH

Note: To obtain the best results cut your

lawn or grass area regularly and do not cut

when the grass is wet.

If, when grass cutting, loose grass is seen

to be scattering from beneath your mower,

the grassbox is probably full and should be

emptied.

Blade maintenance

The steel blade is designed to give a fine

finish in long or tough grass. The blade will

continue to cut even when it has become

blunt or burred. There is no need for it to be

razor sharp.

If, however, because of damage or wear the

cutting performance deteriorates, then your

mower may require a new blade, or at least

the existing blade to be sharpened.

We recommend that the steel blade is

sharpened or a new blade fitted at the

beginning of each season.

Replacement blades are available from

Black & Decker service agents.

Warning! When fitting a new blade use only

the Black & Decker replacement part

specified for your mower - do not attempt to

fit any other blade.

Fitting a new blade (Fig. G)

Observe all the relevant warnings before

changing the blade.

Warning! Disconnect your mower from the

electrical supply before changing the blade.

• Turn your mower over on its side so that

the underside of the mower body (1) is

exposed.

• Using a cloth placed over the blade or

heavy duty gloves to protect your hands,

grip the blade and, using the spanner

provided, loosen and remove the nut (16)

from the motor spindle. Turn the nut in an

anti-clockwise direction to loosen it.

• The blade can now be replaced and the

washer and nut reassembled.

Note: Do not remove the impeller (17) for

any reason.

Note: Some mowers are fitted with a clutch

washer, between the blade nut and the blade,

which must be reassembled at all times.

Removing the grassbox from your mower:

Raise the grassflap. Lift the grassbox off the

mower and rest it on the lawn. Gently lower

the grassflap, then use both hands to lift the

full grassbox.

How to use your mower (Fig. E & F)

Observe all of the relevant warnings when

using your mower.

• Push the loop of cable through the slot

from the opposite side of the restraint

hook (Fig. E1), position the loop over the

hook and pull the cable back through the

slot. Your cable will now be restrained.

We recommend the directional method of

operation to obtain the maximum cutting

performance from your mower and to reduce

the risk of the trailing the extension lead from

entering the cutting path.

• Place the bulk of the supply cable on

the lawn close to the starting point

(see Fig. F2a, position 1).

• Hold the handle assembly with both

hands.

Warning! Do not attempt to operate your

mower with one hand - you must guide it

with both hands.

• Tilt the handle downwards to slightly raise

the front of your mower and to reduce

the risk of lawn damage whilst starting,

depress the safety lock-off button (12) on

the switchbox (10) and whilst still

depressed pull the switch lever (11)

towards you. Your mower will start and

you can now allow the lock-off button to

be released and lower your mower to its

proper cutting position, and commence

cutting.

• Proceed down the cutting area as shown

in Fig. F2a, working from position 1

towards position 2 and, on reaching

position 2, turn to the right and proceed

towards position 3. Continue to the end

of the cutting area, turn to the left and

proceed towards position 4. Continue in

the same manner as shown in Fig. F2a,

always working away from the cable.

Do not adopt the method as shown in

Fig. F2b, working towards the cable, as

this is dangerous practice.

Your mower will continue to operate whilst

you are pulling the switch lever. To stop your

mower release the switch lever.

When you have finished using your mower

we recommend that you clean all debris from

it before putting it away. Refer to the

‘Care and maintenance’ section.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GR346 in the language / languages: English as an attachment in your email.

The manual is 0,23 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker GR346 Manual

Product: