Manual Black Decker GR346 (page 4 of 16) (English)

529726

Zoom out

Zoom in

1/16

Note: Fuses do not give personal protection

against electric shock.

Plug replacement

• Disconnect the plug from the supply.

• Cut off the plug and dispose of

immediately. Insertion of a detatched

plug into a 13 amp socket outlet may

result in electric shock.

• Only fit BS1363A approved plugs fitted

with the correctly rated fuse.

• The cable wire colours, or a letter, will be

marked at the connection points of most

good quality plugs. Attach the wires to

their respective points in the plug (see

below). Brown is for “Live” (L) and blue is

for “Neutral” (N).

• Before replacing the top cover of the

mains plug ensure that the cable clamp

is holding the outer sheath on the cable

firmly and that the two leads are correctly

fixed at the terminal screws.

Fit a BS1363A

approved

resilient plug

Connect blue

to N (neutral)

Make sure that the

outer sheath of the

cable is held firmly

by the clamp

Fit the recommended

fuse approved

to BS1362

Connect brown

to L (live)

230 volts AC only

Never use a light

socket

Warning! Never connect live or neutral wires

to the earth pin marked “E” or .

Note: Do not wire an extension cable directly

into your mower yourself. Instead, take your

mower to your nearest Black & Decker

service agent.

Increased safety can be obtained by having

a qualified electrician install a high sensitivity

(30mA) circuit breaker in the house wiring.

If you do not have such a circuit breaker

installed, or you do not wish to have one

installed, then we strongly recommend that

the electrical power to your mower be

supplied through a high sensitivity (30mA)

residual current device (RCD). The RCD is

designed to provide a high degree of

personal protection against harmful electric

current should fault conditions occur.

Warning! The use of an RCD or other circuit

breaker unit does not release the operator of

your mower from the safety instructions and

safe working practices given in this manual.

Handle assembly (Fig. A & B)

Remove the contents of the carton and

familiarise yourself with the individual parts

of your mower.

The main parts of your mower are as follows:

• Mower body (1) - this comprises the

motor cover (3), wheels (4), grass flap (5).

• Handle - upper handle (8), lower

handle (9R & 9L), switch box (10), switch

lever (11), safety lock-off (12), electric

cable (13), cable clips (14), handle

assembly (wing nut and bolt) (15).

• Join the upper and lower handles by

screwing them together using the wing

nuts and bolts provided.

To assemble the lower handles into the

correct locations on your mower body,

proceed as follows:

• Insert the lower handles (9) into the two

holes in your mower body (1) and press

down until secure. Secure in position

using the screws supplied (6).

Height of cut adjustment (Fig. C)

Warning! Disconnect your mower from

the electrical supply before making any

adjustment and allow the blade to stop

rotating. Cutting blades are sharp.

The wheels are already pre-mounted.

To select a height of cut, move the wheels (4)

into the slot required using the spring system

(21). To ensure an even cut, please make

sure that all four wheels are placed in the

same position.

Grassbox assembly (Fig. D)

Read the safety instructions at the beginning

of this manual before using this accessory.

• The grassbox is a two piece (14 & 15)

plastic construction which needs to be

assembled before attaching it to your

mower.

To assemble the grassbox, proceed as

follows:

• Align both parts together and clip in

place.

Fitting the grassbox to your mower:

• The spring loaded grass flap is lifted and

the two arms on the front edge of the

grassbox are located behind the two lugs

rising up from the rear edge of the cutter

deck.

• The grass flap can now be released to

lock the grassbox into position.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GR346 in the language / languages: English as an attachment in your email.

The manual is 0,23 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker GR346 Manual

Product: