Manual Black Decker GL300 (page 10 of 48) (English, German, Dutch, French, Italian, Portuguese, Spanish)

527566

Zoom out

Zoom in

1/48

Note: There is no need to remove the terminal

screws. Connections are not to be made under

the screw heads.

terminal screw

clamp terminal

washer conductor

position

to left of screw

• Locate the cable and cable protector into the

body correctly (see below, figure a). Then fit the

cable clamp over the outer sheath of the cable

and screw down until the screws are fully home.

Failure to do this may result in the cover not

fitting correctly to the connector body.

• Before replacing the cover of the ‘female’

connector make sure that the cable clamp is

holding the outer sheath of the cable firmly with

screws fully home and that the two leads are

correctly fixed at the terminal screws and are not

taut (see below, figure a).

• Place the cover onto the body assembly

ensuring that it seats flat, then retighten the fixing

screw into the nut until the cover is securely held

(see below, figure c).

• Finally check that the cable protector is secure

and that there are no gaps between the cover

and the connector body.

terminal screws

clamping washers

connector body fixing screw

6mm

cable

clamp cover

cable

protector

Preparing your trimmer for use

(Fig. B - D)

• Take your trimmer, guard and parts pack

out of the box.

• Remove the guard screw from the parts

pack.

• Place the guard over the spool housing

on your trimmer taking care that the line

does not become stuck between the

two parts.

• Align the square marking on the guard

with the square marking on your trimmer

body and push the guard upwards until it

almost contacts the underside of the

body. Now turn the guard in the direction

indicated by the arrow.

• The guard is secure when the ridges on

the guard have fitted into the slots in the

body, and the spring finger has located.

• Once the guard is in position, secure the

guard screw which goes through the

guard screw hole and into screw boss in

the body.

• To avoid damage in transit, the spool has

been packed in a polythene bag.

Assembling the spool (Fig. E)

• Thread the line through the hole in the

inner cover and then unclip the line from

the groove in the top face of the spool.

• Place the inner cover on the spool.

• Ensure that sufficient line is threaded

through the hole in the inner cover before

fitting the spool to the spool carrier.

• Grip the spool with one hand and the

spool carrier with the other. Fit the spool

by pushing down in the direction of arrow

(a) and twisting clockwise in the direction

of arrow (b) until you feel it click into

position.

How to use your trimmer (Figs. 1 - 8)

To switch on your trimmer press the switch

lever. To switch off your trimmer, release the

switch lever.

In order to get the most from your trimmer

please learn the following techniques.

Do not be impatient, you will obtain the best

results by experience and by following these

simple rules.

Do not use your trimmer without its guard.

Do not cut wet grass, best results are

achieved when the grass is dry.

Cut at an angle and with the tip of the nylon

line. Your trimmer is balanced to operate at

this angle.

Swing your trimmer gently from side to side.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GL300 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,86 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker GL300 Manual

Product: