Manual Black Decker GL300 (page 9 of 48) (English, German, Dutch, French, Italian, Portuguese, Spanish)

527566

Zoom out

Zoom in

1/48

old ‘female’ connector new ‘female’ connector

Should you wish to convert more than one cable

system, the new female connector is available as an

accessory from most major DIY retail outlets and from

Black & Decker service agents (cat. no. A6624S).

Existing powered garden tools

(UK only)

To connect existing Black & Decker garden power

tools to the new system you will require an adaptor

(see below). This is available as an accessory from

most major DIY retail outlets (cat. no. A6623S).

Warning! This adaptor is only suitable for

products rated up to 500W.

It is not recommended for use with the

following:

Hover mowers

Rotary mowers with grass collection

Chainsaws

Shredders

Blowervacs.

Please contact your local service agent

should you require further advice.

Fitting your own extension cable

(UK only)

• When fitting your own extension cable fit a

13 amp plug (see “Fitting the mains plug”) to one

end of the cable and a ‘female’ connector

(supplied loose in the carton) to the other end

(see opposite). For wiring instructions see the

following sections.

• A ‘male’ connector is already attached to the

electrical supply cable on your mower and is

designed to be non-rewireable (see opposite).

This should not be removed. Should the

cable and plug become damaged or need

replacing, please return your mower to your local

Black & Decker service agent.

‘female’ connector ‘male’ connector

Warning! Never wire an extension cable with

anything other than the ‘female’ connector

supplied and a 13 amp BS1363A approved

ENGLISH

plug with the recommended fuse. Never

wire a ‘male’ connector to your extension

cable and never wire an extension cable

with a plug of any kind at each end of the

cable. This is extremely dangerous and

results in the pins being live which may

cause a fatal electric shock.

Fitting the ‘female’ connector

(UK only)

To remove the cover, unscrew the fixing screw until it

is free of the nut which is located in the hexagonal

recess on the underside of the connector. Take care

not to lose the nut if it falls out. There is no need to

completely remove the fixing screw as it is intended

to remain captive in the cover. The cover can now be

removed by applying pressure as shown below.

apply pressure here

The extension cable contains two wires which are

colour coded for easy recognition; brown is for ‘Live’

(L) and blue is for ‘Neutral’ (N). The female connector

is marked ‘L’ for live and ‘N’ for neutral. These

markings are located inside the body near the

terminal screws (see opposite, figure a). With the

connector cover removed, lift out the cable protector

and proceed as follows:

• Pass the cable through from the narrow end of

the cable protector (see opposite, figure a).

• Prepare the cable ends to the specified strip

lengths (see opposite, figure b).

• Remove cable clamp (see opposite, figure a).

Take care of loose parts.

• To connect the extension cable to the connector

terminals, unscrew the terminal screws until the

clamp washers have lifted just enough to enter

the conductor between the raised washer and

the terminal (see below). Connect the brown lead

to ‘L’ and the blue lead to ‘N’.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GL300 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,86 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker GL300 Manual

Product: