585836
11
Zoom out
Zoom in
Previous page
1/16
Next page
11
ENGLISH
(Original instructions)
u To charge the battery (12), insert it into the charger (19).
not force. Be sure that the battery is fully seated in the
charger.
u Plug in the charger and switch on at the mains.
The charging indicator (18) will blink.
The charge is complete when the charging indicator (18)
switches to continuously on. The charger and the battery
switch on as the charger occasionally tops up the battery
charge.
u Charge discharged batteries within 1 week. Battery life will
be greatly diminished if stored in a discharged state.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
the battery pack fresh and fully charged.
Charger diagnostics
If the charger detects a weak or damaged battery, the charg-
follows:
u Re-insert the battery (12).
u
rate, use a different battery to determine if the charging
process works properly.
u If the replaced battery charges correctly, the original
battery is defective and should be returned to a service
centre for recycling.
u If the new battery gives the same indication as the original
battery, take the charger to be tested at an authorised
services centre.
Note: It may take as long as 30 minutes to determine that
the battery is defective. If the battery is too hot or too
cold, the charging indicator will alternately blink red, fast
u
recommended chain oil. You can see the oil level in the oil
u Periodically switch off and check the oil level indicator
(11); if it is less than a quarter full, remove the battery from
Oiling the chain
We recommend that you use only Black & Decker oil
(A6027-50)during the lifetime of your chainsaw because
mixtures of different oils could lead to the oil becoming
degraded, which can drastically shorten the lifetime of the saw
chain and create additional risks.
Never use waste oil, thick oil or very thin sewing machine oil.
These may damage your chainsaw.
The saw chain (6) must be oiled before each use and after
cleaning using only the correct grade of oil (cat. no. A6023-
QZ).
u Lubricate the saw chain (6) by slowly pressing the bulb
each cut. Hold the bulb down for 1 second each time.
u f
button (2) with your thumb and then push the on/off switch
(1) to start.
u When the motor starts, remove your thumb from the lock-
Do not force the tool, allow the tool to do the work. It will do
a better and safer job at the speed for which it is designed.
Excessive force will stretch the saw chain (6).
If the saw chain (6) or guide bar (7) becomes
jammed
u Switch the tool off.
u Remove the battery (12).
u Open the cut with wedges to relieve the strain on the
guide bar (7). Do not try to wrench the chainsaw free.
u Start a fresh cut.
It is normal for a small amount of excess oil drip from the
chain saw bar and chain during storage. Do not store chain
saw on top of any thing that may be damaged by the dripping
oil.
u
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
u To remove the battery, push the release buttons (16) while
at the same time pulling the battery out of the receptacle.
Use
Warning! Let the tool work at its own pace. Do not overload.
-
done before. The battery may become warm while charging;
this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging tem-
perature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 10 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell tempera-
ture warms up or cools down.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker GKC1825L20 T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GKC1825L20 T1 in the language / languages: English as an attachment in your email.

The manual is 8,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker GKC1825L20 T1

Black Decker GKC1825L20 T1 User Manual - Polish - 20 pages

Black Decker GKC1825L20 T1 User Manual - All languages - 136 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info