Manual Black Decker GKC108 TH1 (page 6 of 96) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

585839

Zoom out

Zoom in

1/96

ENGLISH

(Original instructions)

Assembly

Warning! Before assembly, remove the battery from the tool

and make sure that the saw blade has stopped. Used saw

blades may be hot.

Fitting the saw blade (g. A)

u Hold the tool away from the body

u To t a saw blade, press the lever (9) down and hold it in

this position.

u Insert the saw blade into the blade clamp (7) as shown.

u Release the lever.

u To remove the saw blade, press the lever (9) down and

pull the saw blade from the holder.

Removing the saw blade (g. A)

Warning! Burn hazard: Do not touch the blade immediately

after use. Contact with the blade may result in personal injury.

u Press the lever (9) down.

u Remove blade

Fitting and removing the battery (g. B)

u To t the battery (8), line it up with the receptacle on the

tool. Slide the battery into the receptacle and push until

the battery snaps into place.

u To remove the battery, push the release buttons (10) while

at the same time pulling the battery out of the receptacle.

Use

Warning! Let the tool work at its own pace. Do not overload.

Charging the battery (g. C)

The battery needs to be charged before rst use and whenev-

er it fails to produce sufcient power on jobs that were easily

done before. The battery may become warm while charging;

this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 10 °C or above 40 °C. Recommended charging tem-

perature: approx. 24 °C.

Note: The charger will not charge a battery if the cell

temperature is below approximately 10 °C or above 40 °C.

The battery should be left in the charger and the charger

will begin to charge automatically when the cell tempera-

ture warms up or cools down.

u To charge the battery (8), insert it into the charger (11).

The battery will only t into the charger in one way. Do

not force. Be sure that the battery is fully seated in the

charger.

u Plug in the charger and switch on at the mains.

The charging indicator (12) will ash green continuously

(slowly).

The charge is complete when the charging indicator (12)

lights green continuously. The charger and the battery can be

left connected indenitely with the LED illuminated. The LED

will change to ashing green (charging) state as the charger

occasionally tops up the battery charge. The charging indica-

tor (12) will be lit as long as the battery is connected to the

plugged-in charger.

u Charge discharged batteries within 1 week. Battery life will

be greatly diminished if stored in a discharged state.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

LED glowing indenitely. The charger will keep the battery

pack fresh and fully charged.

Charger diagnostics

If the charger detects a weak or damaged battery, the charg-

ing indicator (12) will ash red at a fast rate. Proceed as

follows:

u Re-insert the battery (8).

u If the charging indicators continues ashing red at a fast

rate, use a different battery to determine if the charging

process works properly.

u If the replaced battery charges correctly, the original

battery is defective and should be returned to a service

centre for recycling.

u If the new battery gives the same indication as the original

battery, take the charger to be tested at an authorised

service centre.

Note: It may take as long as 60 minutes to determine that

the battery is defective. If the battery is too hot or too

cold, the LED will alternately blink red, fast and slow, one

ash at each speed and repeat.

Switching on and off (g. D)

The tool is equipped with a switch lock-off feature to prevent

unintentional operation.

u To switch the tool on, press the lock off button (2) then

squeeze the on/off switch (1).

u Once the tool is on, release the lock off button.

u Releasing the on/off switch turns the tool off.

Using the clamping arm (g. E)

The tool is equipped with a clamping arm which helps to

stabilise the tool on the work piece.

u Pull back the clamping arm release button (3). This will

release the clamping arm. Once clamping arm is released

you can let go of button.

u To switch the tool on, press the lock off button (2) then

squeeze the on/off switch (1).

u With the saw running, the clamping arm will rotate forward

until it comes in contact with the workpiece.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GKC108 TH1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,35 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker GKC108 TH1

Black Decker GKC108 TH1 Quick start guide - English - 12 pages

Black Decker GKC108 TH1 User Manual - Polish - 12 pages

Black Decker GKC108 TH1 User Manual - Turkish - 12 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker GKC108 TH1 Manual

Product: